Index of Error Messages

Error Code List

Error Codes

Error Messages

006

Equipment Configuration Error Causes:

  1. CPU BIOS Update Code Mismatch
  2. IDE Primary Channel Master Drive Error
  3. IDE Secondary Channel Master Drive Error

010

Memory Error at XXXX:XXXX:XXXXh (R:XXXXh, W:XXXXh)

070

Real Time Clock Error

071

CMOS Battery Bad

072

CMOS Checksum Error

110

Incorrect password specified, system disabled. (Text mode only)

<No Error Code>

Battery critical low

In this situation, BIOS will issue 4 short beeps that shut down the system. No message will be shown.

<No Error Code>

Thermal critical high

In this situation, BIOS will issue 3 long beeps then shut down the system.

Error Message List

Error Messages

FRU/Action in Sequence

Failure Fixed Disk

Reconnect hard disk drive connector. "Load Default Settings" in BIOS Setup Utility. Hard disk drive System board

Stuck Key

see "Keyboard or Auxiliary Input Device Check" on page 73 .

Keyboard error

see "Keyboard or Auxiliary Input Device Check" on page 73.

Keyboard Controller Failed

see "Keyboard or Auxiliary Input Device Check" on page 73.

Keyboard locked - Unlock key switch

Unlock external keyboard

Monitor type does not match CMOS - Run Setup

Run "Load Default Settings" in BIOS Setup Utility.

Shadow RAM Failed at offset: nnnn

BIOS ROM System board

System RAM Failed at offset: nnnn

DIMM

System board

Extended RAM Failed at offset: nnnn

DIMM

System board

System battery is dead - Replace and run Setup

Replace RTC battery and Run BIOS Setup Utility to reconfigure system time, then reboot system.

System CMOS checksum bad - Default configuration used

RTC battery

Run BIOS Setup Utility to reconfigure system time, then reboot system.

Run BIOS Setup Utility to reconfigure system time, then reboot system.

System board

Error Messages

FRU/Action in Sequence

Run BIOS Setup Utility to reconfigure system time, then reboot system.

System board

Previous boot incomplete - Default configuration used

Run "Load Default Settings" in BIOS Setup Utility. RTC battery System board

Memory size found by POST differed from CMOS

Run "Load Default Settings" in BIOS Setup Utility. DIMM

System board

Diskette drive A error

Check the drive is defined with the proper diskette type in BIOS Setup Utility

See "External Diskette Drive Check" on page 72.

Incorrect Drive A type - run SETUP

Check the drive is defined with the proper diskette type in BIOS Setup Utility

See "External Diskette Drive Check" on page 72.

System cache error - Cache disabled

System board

CPU ID:

System board

System board

System board

System board

Device Address Conflict

Run "Load Default Settings" in BIOS Setup Utility. RTC battery System board

Allocation Error for device

Run "Load Default Settings" in BIOS Setup Utility. RTC battery System board

Failing Bits: nnnn

DIMM BIOS ROM System board

Fixed Disk n

None

Invalid System Configuration Data

BIOS ROM System board

I/O device IRQ conflict

Run "Load Default Settings" in BIOS Setup Utility. RTC battery System board

Operating system not found

Enter Setup and see if fixed disk and drive A: are properly identified. Diskette drive Hard disk drive System board

No beep Error Messages

FRU/Action in Sequence

No beep, power-on indicator turns off and LCD is blank.

Power source (battery pack and power adapter). See "Power System Check" on page 73.

Ensure every connector is connected tightly and correctly. Reconnect the DIMM. LED board. System board.

No beep, power-on indicator turns on and LCD is blank.

Power source (battery pack and power adapter). See "Power

System Check" on page 73.

Reconnect the LCD connector

Hard disk drive

LCD inverter ID

LCD cable

LCD Inverter

System board

No beep, power-on indicator turns on and LCD is blank. But you can see POST on an external CRT.

Reconnect the LCD connectors.

LCD inverter ID

LCD cable

LCD inverter

System board

No beep, power-on indicator turns on and a blinking cursor shown on LCD during POST.

Ensure every connector is connected tightly and correctly. System board

No beep during POST but system runs correctly.

Speaker System board

Error Beep List

Code

Beeps

Description

00h

Two long beeps, one short beep, and then one long beep

Success

F1h

One long, One short beeps

BIOS file size mismatch

F2h

One long, two short beeps

BIOS file reading error

D1h

Two short beeps

Floppy drive not installed

The Ultimate Computer Repair Guide

The Ultimate Computer Repair Guide

Read how to maintain and repair any desktop and laptop computer. This Ebook has articles with photos and videos that show detailed step by step pc repair and maintenance procedures. There are many links to online videos that explain how you can build, maintain, speed up, clean, and repair your computer yourself. Put the money that you were going to pay the PC Tech in your own pocket.

Get My Free Ebook


Responses

  • muhammad
    How do i change the cmos battery in a travelmate c110?
    7 years ago
  • max
    How to run safe mode on travelmate c110?
    7 years ago

Post a comment