Exit

The Exit screen allows you to save or discard any changes you made and quit the BIOS Utility.

PhoenixBIOS Setup Utility 1

Information Main Advanced Security Power Boot

AMD

Item Specific Help

Exit System Setup and

Exit Discarding Changes

save your changes to

Load Setup Defaults

CMOS.

Discard Changes

Save Changes

F1 Help ti Select Item F5/F6 Change Values ESC Exit <—> Select Menu Enter Select^Sub-Menu

F9 Setup Defaults

F10 Save and Exit

The table below describes the parameters in this screen.

Parameter

Description

Exit Saving Changes

Exit System Setup and save your changes to CMOS.

Exit Discarding Changes

Exit utility without saving setup data to CMOS.

Load Setup Default

Load default values for all SETUP item.

Discard Changes

Load previous values from CMOS for all SETUP items.

Save Changes

Save Setup Data to CMOS.

BIOS Flash Utility

The BIOS flash memory update is required for the following conditions:

  • New versions of system programs
  • New features or options
  • Restore a BIOS when it becomes corrupted. Use the Phlash utility to update the system BIOS flash ROM.

NOTE: Create a Crisis Recovery Media (such as USB HDD) before you use the Phlash utility.

NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.

NOTE: Please use the AC adaptor power supply when you run the Phlash utility. If the battery pack does not contain enough power to finish BIOS flash, the system will not boot as the BIOS is not loaded.

Perform the following steps to use the Flash Utility:

  1. Press F2 during boot to enter the Setup Menu.
  2. Select Boot Menu to modify the boot priority order, for example, if using USB HDD to Update BIOS, move USB HDD to position 1.

3. Execute the JALB028.BAT batch file from C:\JALBO_JALCO\BIOS\JALBO28A to update BIOS. The flash process begins as shown.

Phoenix Phlath16 Utility Vanton 1.6.7.8 Cqpurlefit <c) Phoenix lechnglotlm Ltd., 2006-2987

-

— Parfornlng ths ioUouins (unction 1

Load Inagh fil*

JBLB028 MFH

J

Uarlfu intnrfacB l-forrat l'in

Backup sustan BIOS RDM

t

Chvch f Laeh nonory tup&ls)

*

F laah nenocy block i

81234

Save block

Restare 0 IOC«

Zern out block

Eriaa block

IUU

Prngran black

urn

Utrlfu black

ca. -■

Flash proacanning coop lot a

Nr.» Bill'. Oil« . lin». P.rt M.inhcir : HSsMsBH 11 i* <11S OPUFIHT

Flash pirt! MX25inBB Daulctlti 13 Mr.ID: tZ mHHIHt Hock .t maww iron B3W »1th 1BB8B by tub_HII

Nr.» Bill'. Oil« . lin». P.rt M.inhcir : HSsMsBH 11 i* <11S OPUFIHT

Flash pirt! MX25inBB Daulctlti 13 Mr.ID: tZ mHHIHt Hock .t maww iron B3W »1th 1BB8B by tub_HII

4. In flash BIOS, the message Please do not remove AC Power Source displays. NOTE: If the AC power is not connected, the following message displays.

Phoeni* PhL«ishl6 Utllltu Version 1,6,7.0 Copyright (c) Phoenix Technologies Ltd,. 2608-2607

—Perforning the following function

CflUTIGH : AC Adapter does not anist I Insert AC then press a»u key to go, or press any key to restart,the systen.

Save block Restore block Zero out block Erase block Progran black Uürlfy black Flash progrannlng couplets

Plug in the AC power to continue.

5. Flash is complete when the message Flash programming complete displays.

Was this article helpful?

+1 -1

Post a comment