Hardware Specifications and Configurations

Intel Pentium M 715,725 TravelMate 4010 InteI 855GME+ICH4-M for TravelMate 4010 1.308V (highest frequency mode) to 0.956V (low frequency mode) 0.748V (deeper sleep mode) SST 39SF040A, 512KX8 CMOS Boot Block Flash Memory ACPI 1.0b, PC Card 95, SM BIOS 2.3, IEEE1284-ECP EPP, PCI 2.2, PnP 1.0a, DMI 2.0, PS 2 keyboard and mouse, USB 2.0, VGA BIOS, CD-ROM bootable, IEEE 1394 2MB for Intel Pentium M processor at 1.5 1.6GHz (Dothan)-TravelMate 4010 Intel 855GME built-in (TravelMate 4010) You can...

Chapter

This chapter contains step-by-step procedures on how to disassemble the notebook computer for maintenance and troubleshooting. To disassemble the computer, you need the following tools Wrist grounding strap and conductive mat for preventing electrostatic discharge Plastic flat head screw driver NOTE The screws for the different components vary in size. During the disassembly process, group the screws with the corresponding components to avoid mismatch when putting back the components. When you...

Front Open View

Also called LCD liquid-crystal display , displays computer output. Internal microphone for sound recording. Comfortable support area for our hands when you use the computer. Click buttons Left, center and right The left and right buttons function like the left and right mouse buttons the center button serves as a 4-way scroll button. Touch-sensitive pointing device which functions like a computer mouse. Turns on the computer power. Light-Emitting Diodes LEDs that turn on and off to show the...

Index of Error Messages

See Keyboard or Auxiliary Input Device Check on page 70 System CMOS checksum bad - Default configuration used Run BIOS Setup Utility to reconfigure system, then reboot system. Run BIOS Setup Utility to reconfigure system time, then reboot Previous boot incomplete - Default configuration used Load Default Settings in BIOS Setup Utility. RTC battery Main baord Load Default Settings in BIOS Setup Utility. Main board Enter Setup and see if fixed disk and drive A are properly identified. Dikette...

Phoenix BIOS Beep Codes

Disable Non-Maskable Interrupt NMI Initialize chipset with initial POST values Initialize caches to initial POST values Load alternate registers with initial POST values Restore CPU control word during warm boot Initialize PCI Bus Mastering devices Initialize cache before memory autosize Reset Programmable Interrupt Controller RAM failure on data bits xxxx of low byte of memory bus Enable cache before system BIOS shadow RAM failure on data bits xxxx of high byte of memory bus Advanced...

Keyboard or Auxiliary Input Device Check

Remove the external keyboard if the internal keyboard is to be tested. If the internal keyboard does not work or an unexpected character appears, make sure that the flexible cable extending from the keyboard is correctly seated in the connector on the system board. If the keyboard cable connection is correct, run the Keyboard Test. If the tests detect a keyboard problem, do the following one at a time to correct the problem. Do not replace a non-defective FRU 1. Reconnect the keyboard cables....

Boot

This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices includes the distette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay. Floppy Devices Hard Drive Network Boot and - indicate device categories. Use lt Enter gt to expand collapses. Boot order is top-down using only the top device in each category. Use lt F6 gt and lt F5 gt to move highlighted item up and down.

Bottom Panel

Computer Status Icon

Note Do not cover or obstruct the opening Houses the computer's hard disk secured by a screw . Unlatches the battery to remove the battery pack. The computer has three easy-to-read status icons on the upper-right above the keyboard, and four on the front panel. Lights when the disc or AcerMedia is activated. Indicates the status of Bluetooth communication. Indicates the status of wireless LAN communication. Lights up when the battery is being charged.

Index of SymptomtoFRU Error Message

Next, enter BIOS utility to running Load Default Settings then reboot the system. Keyboard if the brightness function key doesn't work . Enter BIOS Utility to execute Load Setup Default Settings, then reboot system. Keyboard if the brightness function key doesn't work . LCD has extra horizontal or vertical lines Indicator incorrectly remains off or on, but system runs correctly HDD CD-ROM active indicators cannot work HDD CD-ROM drive Device driver Main board...

BIOS Setup Utility

The BIOS Setup Utility is a hardware configuration program built into your computer s BIOS Basic Input Output System . Your computer is already properly configured and optimized, and you do not need to run this utility. However, if you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4 Troubleshooting when problem arises. To activate the BIOS Utility, press M during POST when Press lt F2 gt to enter Setup message is prompted on the bottom of screen ....

Cear HDD Password SOP

Remove Hdd Password

Use right arrow button to move to Security page. See the image below. Supervisor Password Is User Password Is Prim ary Password Is HDD Master ID Set Supervisor Password Set User Password Set HDD Password Change Values F9 Setup defaults Select 4 Sub-Menu HFuU Save and Exit 5. Key in HDD Master ID as following picture. See the image below.