Index of Error Messages

Error Code List

Error Codes

Error Messages

006

Equipment Configuration Error Causes:

  1. CPU BIOS Update Code Mismatch
  2. IDE Primary Channel Master Drive Error

(THe causes will be shown before "Equipment Configuration Error")

010

Memory Error at xxxx:xxxx:xxxxh (R:xxxxh, W:xxxxh)

070

Real Time Clock Error

071

CMOS Battery Bad

072

CMOS Checksum Error

Incorrect password is specified.

<No error code>

Battery critical LOW

In this situation BIOS will issue 4 short beeps then shut down system, no message will show.

<No error code>

Thermal critical High

In this situation BIOS will shut down system, not show message.

Error Message List

Error Messages

FRU/Action in Sequence

Failure Fixed Disk

Reconnect hard disk drive connector. "Load Default Settings" in BIOS Setup Utility. Hard disk drive System board

Stuck Key

see "Keyboard or Auxiliary Input Device Check" on page 82.

Keyboard error

see "Keyboard or Auxiliary Input Device Check" on page 82.

Keyboard Controller Failed

see "Keyboard or Auxiliary Input Device Check" on page 82.

Keyboard locked - Unlock key switch

Unlock external keyboard

Monitor type does not match CMOS - Run Setup

Run "Load Default Settings" in BIOS Setup Utility.

Shadow RAM Failed at offset: nnnn

BIOS ROM System board

System RAM Failed at offset: nnnn

DIMM

System board

Extended RAM Failed at offset: nnnn

DIMM

System board

System battery is dead - Replace and run Setup

Replace RTC battery and Run BIOS Setup Utility to reconfigure system time, then reboot system.

System CMOS checksum bad - Default configuration used

RTC battery

Run BIOS Setup Utility to reconfigure system time, then reboot system.

Run BIOS Setup Utility to reconfigure system time, then reboot system.

System board

Error Messages

FRU/Action in Sequence

Run BIOS Setup Utility to reconfigure system time, then reboot system.

System board

Previous boot incomplete - Default configuration used

Run "Load Default Settings" in BIOS Setup Utility. RTC battery System board

Memory size found by POST differed from CMOS

Run "Load Default Settings" in BIOS Setup Utility. DIMM

System board

Diskette drive A error

Check the drive is defined with the proper diskette type in BIOS Setup Utility

See "External Diskette Drive Check" on page 82.

Incorrect Drive A type - run SETUP

Check the drive is defined with the proper diskette type in BIOS Setup Utility

System cache error - Cache disabled

System board

CPU ID:

System board

System board

System board

System board

Device Address Conflict

Run "Load Default Settings" in BIOS Setup Utility. RTC battery System board

Allocation Error for device

Run "Load Default Settings" in BIOS Setup Utility. RTC battery System board

Failing Bits: nnnn

DIMM BIOS ROM System board

Fixed Disk n

None

Invalid System Configuration Data

BIOS ROM System board

I/O device IRQ conflict

Run "Load Default Settings" in BIOS Setup Utility. RTC battery System board

Operating system not found

Enter Setup and see if fixed disk and drive A: are properly identified. Diskette drive Hard disk drive System board

No beep Error Messages

FRU/Action in Sequence

No beep, power-on indicator turns off and LCD is blank.

Power source (battery pack and power adapter). See "Power System Check" on page 83..

Ensure every connector is connected tightly and correctly. Reconnect the DIMM. LED board. System board.

No beep, power-on indicator turns on and LCD is blank.

Power source (battery pack and power adapter). See "Power

System Check" on page 83..

Reconnect the LCD connector

Hard disk drive

LCD inverter ID

LCD cable

LCD Inverter

System board

No beep, power-on indicator turns on and LCD is blank. But you can see POST on an external CRT.

Reconnect the LCD connectors.

LCD inverter ID

LCD cable

LCD inverter

System board

No beep, power-on indicator turns on and a blinking cursor shown on LCD during POST.

Ensure every connector is connected tightly and correctly. System board

No beep during POST but system runs correctly.

Speaker System board

DIY Battery Repair

DIY Battery Repair

You can now recondition your old batteries at home and bring them back to 100 percent of their working condition. This guide will enable you to revive All NiCd batteries regardless of brand and battery volt. It will give you the required information on how to re-energize and revive your NiCd batteries through the RVD process, charging method and charging guidelines.

Get My Free Ebook


Post a comment