Main Unit Disassembly Flowchart

Step

Screw

Quantity

Part No.

Lower Cover

2*3

4

86.S0207.001

Lower Cover

2*5

1

86.TG607.004

Lower Cover

2*8

5

86.FRC07.001

Upper Cover

2.0*2.5 (silver)

1

86.TG607.004

Upper Cover

2*3

1

86.S0207.001

Upper Cover

2*5

9

86.TG607.004

Button Board

M2-0.4*2

2

86.W4107.002

IO Board

2*5

1

86.TPK07.001

Main Board

2*3

1

86.S0207.001

LCD Hinge

2*5

2

86.TG607.004

Speaker Module

2*3

3

86.S0207.001

IMPORTANT: The keyboard is easily warped or damaged during the removal process. Take care not to use excessive force when removing the keyboard and replace if any damage occurs.

  1. See "Removing the Battery Pack" on page 42.
  2. Press the four (4) latches.

3. Pry up the keyboard.

4. Flip the keyboard over.

5. Unlock the keyboard cable.

1.

See

"Removing the Battery Pack" on page 42.

2.

See

"Removing the SIM Card" on page 43.

3.

See

"Removing the Hard Disk Drive Module" on page 44

4.

See

"Remove the rails from the HDD." on page 46.

5.

See

"Removing the DIMM Module" on page 49.

6.

See

"Removing the WLAN Module" on page 51.

7.

See

"Removing the Keyboard" on page 56.

8.

Remove the ten (10) screws in the lower cover

Step

Screw

Quantity

Screw Type.

Lower Cover Disassembly

2*3

4 (red call outs)

2*5

1 (green call out)

2*8

5 (blue call out)

Turn the computer over and remove the eleven (11) screws in the upper cover.

Step

Screw

Quantity

Screw Type.

Upper Cover Disassembly

2.0*2.5 Silver

1 (green call out)

*

2*3

1 (blue call out)

*

2*5

9 (red call out)

  1. Unlock the I/O board to main board cable at both ends.
  2. Unlock the I/O board to main board cable at both ends.
11. Disconnect the I/O board to main board cable at both ends.
13. Pry up the Upper Cover starting from the side and lift away.
Organigramme Ferrari
14. Remove the I/O board to main board cable.

IMPORTANT: The Touchpad Board cannot be removed individually. To replace the Button Board, replace the entire Upper Cover.

  1. See "Removing the Upper Cover" on page 58.
  2. Unlock the touchpad cable at both ends.

3. Remove the touchpad cable.

4. Disconnect the button board cable from the button board.
6. Remove the button board cable.

Step

Screw

Quantity

Screw Type.

Button Board Disassembly

M2-0.4*2

2

8. Lift the button board away.

  1. See "Removing the Upper Cover" on page 58.
  2. Disconnect the Bluetooth module to main board cable.
3. Pull the Bluetooth module away.
  1. See "Removing the Upper Cover" on page 58.
  2. Open the locking latch at both ends of the card reader cable connectors.
3. Remove the card reader cable.
4. Disconnect the DC power cable connector from the mainboard.

Remove the tape and lift the DC cable out of the cable guide.

6. Disconnect the DC power cable from the I/O board.

Step

Screw

Quantity

Screw Type.

IO Board Disassembly

2*5

1

  1. See "Removing the Upper Cover" on page 58.
  2. See "Removing the I/O Board" on page 66.
  3. Lift up the LCD cable protective over.

4. Disconnect the LCD cable connector.

5. Remove the two (2) screws from the left and right hinges of the LCD module.

Step

Screw

Quantity

Screw Type.

LCD Disassembly

2*5

2

6. Lift away the LCD module and lay it down.

NOTE: Lay the LCD down on a clear smooth surface to prevent damage.

7. Pull the antenna cables free of the chassis, threading the antenna cables through from the bottom side..
8. Remove the LCD module completely.
  1. See "Removing the Upper Cover" on page 58.
  2. See "Removing the Bluetooth Module" on page 65.
  3. See "Removing the I/O Board" on page 66.
  4. See "Removing the LCD Module" on page 69.
  5. Disconnect the speaker connector.

6. Remove the one (1) screw in the main board.

Step

Screw

Quantity

Screw Type.

Main Board Disassembly

2*3

1

*

7. Lift out the main board from the inside edge

1. See "Removing the Mainboard" on page 71.
3. Remove the three (3) screws (red call outs) and loosen the two (2) captive screws (blue call outs).

Step

Screw

Quantity

Screw Type.

Thermal Module Disassembly

2*3

3

*

  1. Lift the fan away from the main board.
  2. Lift the fan away from the main board.
  1. See "Removing the Thermal Module" on page 73.
  2. Using a flat head screwdriver to turn the CPU mounting lock to the OFF position.
Locked CPU Unlocked CPU

3. Lift the CPU out and store carefully.

WARNING:Do not touch the thermal grease to prevent bodily harm.

Was this article helpful?

0 0
The Ultimate Computer Repair Guide

The Ultimate Computer Repair Guide

Read how to maintain and repair any desktop and laptop computer. This Ebook has articles with photos and videos that show detailed step by step pc repair and maintenance procedures. There are many links to online videos that explain how you can build, maintain, speed up, clean, and repair your computer yourself. Put the money that you were going to pay the PC Tech in your own pocket.

Get My Free Ebook


Post a comment