Changing a Password

1. Use the t and i keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set Password box appears.

Set Supervisor Password

Enter Current Password Enter New Password Confirm New Password

  1. Type the current password in the Enter Current Password field and press Enter.
  2. Type a password in the Enter New Password field. Retype the password in the Confirm New Password field.
  3. Press Enter. After setting the password, the computer sets the User Password parameter to "Set".
  4. If desired, you can enable the Password on boot parameter.
  5. When you are done, press F10 to save the changes and exit the BIOS Setup Utility. If the verification is OK, the screen will display as following.



in saved. ]

The password setting is complete after the user presses Enter.

If the current password entered does not match the actual current password, the screen will show you the Setup Warning.

Setup Warning



zord. ]

If the new password and confirm new password strings do not match, the screen displays the following message.

Setup Warning

Passwo Re-e

rds do no nter pass

t match. word.

This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices includes various USB diskette drives and the onboard hard disk drive.

Phoenix SecureCore (tm) Setup Utility


urity Boot


Acer Aspire 6930g Bios Boot System


The Exit screen allows you to save or discard any changes you made and quit the BIOS Utility.

Information Main

Phoenix SecureCore (tm) Setup Utility |urity|

The Exit screen allows you to save or discard any changes you made and quit the BIOS Utility.

Information Main

Phoenix Securecore Setup Utility
The table below describes the parameters in this screen.



Exit Saving Changes

Exit System Setup and save your changes to CMOS.

Exit Discarding Changes

Exit utility without saving setup data to CMOS.

Load Setup Default

Load default values for all SETUP item.

Discard Changes

Load previous values from CMOS for all SETUP items.

Save Changes

Save Setup Data to CMOS.

The BIOS flash memory update is required for the following conditions:

  • New versions of system programs
  • New features or options
  • Restore a BIOS when it becomes corrupted.

Perform the following steps to use the DOS Flash Utility:

  1. Press F2 during boot to enter the Setup Menu.
  2. Select Boot Menu to modify the boot priority order, for example, if using USB HDD to Update BIOS, move USB HDD to position 1.

Phoenix SecureCore (tm) Setup Utility

Phoenix SecureCore (tm) Setup Utility

Phoenix Securecore Settings

Item Specific Help

Keys used to view or configure devices: Up and Down arrows select a device.

<F6> and <F5> moves the device up or down.

Change Values Select ► SubMenu

Setup Default Save and Exit

3. Execute the FLASH.BAT batch file to update BIOS. The flash process begins as shown.

Insyda Flash Utility Tor lnsydeH20

Uorslon l.Zn initializing

Fllo loading IBB *

Current BIOS Modal none : JHTIfl BIDS Node I UM) : Jona

Currwrt 1103 vttrxjim: Ufl.ZI BIBS wttnn: VQ.Z3

llpdlllny kink rrTTTUf»

4. In flash BIOS, the message Please do not remove AC Power Source displays. NOTE: If the AC power is not connected, the following message displays.

C:\it0nvlfl7lfljflosti ji>MB023

1 \H0HVJRnB> flash it J«tlBB23.fd /ft /B /DC

Uamning: Mo AC power connect




Plug in the AC power to continue.

5. Flash is complete when the message Flash programming complete displays.

Perform the following steps to use the WinFlash Utility:

  1. In Windows run ZH6_xxxx_win.exe where xxxx is the bios version. For example, ZH6_3102_win.exe
  2. When the process is complete, close all programs and applications and reboot the system.

Was this article helpful?

0 0

Post a comment