Disassembling the logic upper assembly

Take out the touchpad cable from the small hook on touchpad holder. 2. Remove the four screws holding the touchpad shielding and the touchpad board. 3. Disconnect the touchpad FFC from the touchpad board. 5. Remove the wireless and bluetooth button off the touchpad board. 6. Remove the four screws that fasten the touchpad holder. 7. Remove the touchpad off the logic upper assembly.

Separate the main unit into the logic upper and the logic lower assembly

Remove the three screws on the rear panel. 2. Unscrew the 19 screws on the bottom panel. 3. Detach the front bezel from the main unit. 4. Remove the two screws. Then take the right and the left antenna off the main unit. 5. Disconnect the touchpad cable. 6. Pull out the right and the left wireless LAN antenna, then detach the logic upper assembly from the logic lower assembly.

Remove the function key board and the keyboard

Take the wireless antenna out of the hook on the function key board. 2. Disconnect function key board connector 3. Unscrew the three screws holding the function key board. 4. Remove the three screws that secure the keyboard. 5. Turn over the unit and remove the two screws as the picture shows. 6. Turn over the keyboard. Disconnect the keyboard FFC then remove the keyboard.

Removing the LCD Module

Remove the four screws that secures the middle cover two one each side. 2. Detach middle cover with the assistance of a plastic flat head screw driver. 3. Disconnect the LCD cable then take out the cable from the upper case. 4. Disconnect the left wireless LAN antenna line. Then take out the antenna from the upper case with a tweezers. 5. Unscrew the four screws holding the LCD hinges two on each side. 6. Then remove the entire LCD module.

POST Codes

Disable Non-Maskable Interrupt (NMI) Initialize chipset with initial POST values Initialize caches to initial POST values Load alternate registers with initial POST values Restore CPU control word during warm boot Initialize PCI Bus Mastering devices Initialize cache before memory autosize Reset Programmable Interrupt Controller RAM failure on data bits xxxx of low byte of memory bus Enable cache before system BIOS shadow RAM failure on data bits xxxx of high byte of memory bus Advanced...

Machine Disassembly and Replacement

This chapter contains step-by-step procedures on how to disassemble the notebook computer for maintenance and troubleshooting. To disassemble the computer, you need the following tools Wrist grounding strap and conductive mat for preventing electrostatic discharge Plastic flat blade screwdriver NOTE The screws for the different components vary in size. During the disassembly process, group the screws with the corresponding components to avoid mismatch when putting back the components. When you...

Hardware Specifications and Configurations

ACPI 1.0b, PC Card 95, SM BIOS 2.3, EPP IEEE 1284, ECP IEEE 1284 1.7 amp 1.9, PCI 2.2, PnP 1.0a, DMI 2.0, PS 2 keyboard and mouse, USB 2.0, VGA BIOS, CD-ROM bootable, IEEE 1394 2048MB by two 1024MB SO-DIMM module You can install memory modules in any combinations as long as they match the above specifications. NOTE Above table lists some system memory configurations. You may combine DIMMs with various capacities to form other combinations. On above table, the configuration of slot 1 and slot 2...


The Security screen contains parameters that help safeguard and protect your computer from unauthorized use. Select Item Change Values Setup Defaults Select Menu Select 4 Sub-Menu QQQ Save and Exit The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings. Shows the setting of the Supervisor password Shows the setting of the uer password. This feature is available to user when Supervisor password is set. Password can be...

Disassembly Procedure Flowchart

Ferrari Flowchart

The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence and instructs you on the components that need to be removed during servicing. For example, if you want to remove the system board, you must first remove the keyboard, then disassemble the inside assembly frame in that order.

Disassembling the logic lower assembly

In order to take out the main board from the upper case, first remove the four screws that fasten the top cover shielding. 2. Remove the three screws holding the 4-in-1 card reader, then remove it. 3. Unscrew the four screws that secure the thermal module. 4. Disconnect the fan connector then remove the thermal module. 5. Remove one screw that secures the main board as picture shows. 6. Remove another screw that fastens the main board. 7. Take out the bluetooth antenna. 8. Disconnect the...

FRU Field Replaceable Unit List

This chapter gives you the FRU Field Replaceable Unit listing in global configurations of Ferrari 3200 series products. Refer to this chapter whenever ordering for parts to repair or for RMA Return Merchandise Authorization . Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service Guide. For ACER AUTHORIZED SERVICE...

The Euro Symbol

If your keyboard layout is set to United States-International or United Kingdom or if you have a keyboard with a European layout, you can type the Euro symbol on your keyboard. NOTE For US keyboard users The keyboard layout is set when you first set up Windows. For the Euro symbol to work, the keyboard layout has to be set to United States-International. To verify the keyboard type in Windows XP, follow the steps below 1. Click on Start, Control Panel. 2. Double-click on Regional and Language...

Microsoft Windows XP Home Environment Test

CG 35W AMD Athlon64 2800 Rev. CG 35W AMD Athlon64 3000 Rev. CG 35W 256MB Infineon HYS64D32020HDL-6-C 256MB Nanya NT256D64SH8BAGM-6K 256MB Micron MT8VDDT3264HDG-335C3 512MB Infineon HYS64D64020GBDL-6-B 512MB Nanya NT512D64S8HBAFM-6K 512MB Micron MT16VDDF6464HG-335C2 1GB Elpida EBD11UD8ABDA-6B HannStar HSD150PK14-A CMO N150P2-L04 HGST Moraga IC25N080ATMR04-0 Toshiba PLUTO MK8025GAS Lite_On PA-1900-05QA PFC , 3pins 90W Li_Shin 0202C1990 PFC , 3pins 90W SIMPLO Lilon 4.4AHr...

How to Build NAPP Master Hard Disc Drive

Acer 4310 Boot

Prepare NAPP CD, Recovery CD and System CD. 2. Put NAPP CD into the optical drive. Then boot up the system. 3. The system will ask you if you want to build NAPP Master HDD. Please press any key to continue. 4. NAPP CD will start to preload the system, please click Y . flee NflPP Preload Selector for fleer Sj steiti Uerslon 1.4.0-1 Copyright 2003 fleer I ne. This will preload you.i system- fii e yon. sure V,N3 1. Disk To Disk Recovery 2- CD to Disk Recovery X. Quit Please select your C ioose...