BIOS Setup Utility

The BIOS Setup Utility is a hardware configuration program built into your computer's BIOS (Basic Input/ Output System).

Your computer is already properly configured and optimized, and you do not need to run this utility. However, if you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4 Troubleshooting when problem arises.

To activate the BIOS Utility, press M during POST (when "Press <F2> to enter Setup" message is prompted on the bottom of screen).

NOTE: Some images below are captured from previous model (TravelMate 290E) cause the setup images are not ready for current model, therefore, the information of the CPU type, speed, base memory may not be accurate. Please refer to real BIOS setup screen for correct information.

Setup Bios Menu Security

Navigating the BIOS Utility

There are five menu options: Main, Advanced, Security, Boot and Exit. Follow these instructions:

□ To choose a menu, use the cursor left/right keys (gg).

To choose a parameter, use the cursor up/down keys (QQ). To change the value of a parameter, press p or Q. Press ^^ while you are in any of the menu options to go to the Exit menu.

In any menu, you can load default settings by pressing g. You can also press g to save any changes made and exit the BIOS Setup Utility.

NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a particular menu are shown on the bottom of the screen. Help for parameters are found in the Item Specific Help part of the screen. Read this carefully when making changes to parameter values.


This menu provides you the information of the system.

Bios Acer Extensa 4620



System BIOS Version

Displays system BIOS version

VGA BIOS Version

Displays VGA BIOS version

Serial #

Displays the serial number of the unit.

UUID Number

UUID=16bytes. This will be visible only when there is an internal LAN device present.

System Memory

This field reports the memory size of system base memory. The size is fixed to 640KB.

Extended Memory

This field reports the memory size of the extended memory in the system. Extended Memory size=Total memory size

CPU Speed

CPU Speed= Max speed

Date and Time

Sets the system time and date.

Quiet Boot

Control whether Customer Logo and Summary Screen are displayed or not.


Enabled: LCD brightness will automatically lower to save more power when AC is not present.

Disabled: LCD brightness will NOT automatically lower to save more power when AC is not present.

Network Boot

Enables or disable PXE Boot from LAN during POST.

F12 Boot Menu

This field decides whether the OEM POST screen will have the following message: "Press <F12> Change Boot Device" or not during user's quiet boot.


The Advanced screen contains parameters involving your hardware devices. It also provides advanced settings of the system.

Acer 7535 Bios

FIR Ports

Configure the system's Infrared port using options: Disabled and Enabled.

C ) Disabled f ) C0H1. 3F8. liiO t,

  • COM2, 3F8. TRO h
  • COM3. 3tS. Hit) U

Hoilc Setting For liiOn-( ) Horrtal {16550) ( ) lrDA (HPSIR) ( ) ASK IR (.) FflSl ]R

The table below describes the parameters in the screen. Settings in boldface are the default and suggested parameter settings.



FIR I/O Settings

Sets the base I/O address and IRQ for Infrared port.

Disabled, COM1, 3F8, IRQ4/ COM2, 2F8, IRQ3/ COM3, 3E8, IRQ4/ COM4, 2E8, IRQ3

DMA Setting for Fast IR

Sets a DMA channel for the printer to operate in ECP mode. This parameter is enabled only if Mode is set to ECP.




Mode Setting

Normal (16550), IrDA (HPSIR), ASK IR, FAST IR

LPT Port

Configure the system's parallel port using options: Disabled and Enabled.

-LPT Port-

Port Address-

—DMA Getting For ECP Mode-

Port Definition-

< ) Standard AT (Centronics) <-> Bidirectional <PS-2>

< ) Extended Capabilities <ECP)

—DMA Getting For ECP Mode-

Was this article helpful?

0 0

Post a comment