Insydeh20 Setup Utility

The Power screen allows the user to configure CPU and power management options.

InsydeH20 Setup Utility

Rev. 3.5

Information Main

  • Advanced CPU Control
  • Advanced CPU Control
  • Platform Power Management

ACPI S3: Wake on PME Wake on Modem Ring Auto wake on S5 Quickly S4 Resume

[Enabled] [Disabled] [Disabled] [Disabled] [Disabled]

Insydeh20 Setup Utility

Help Exit a

Select Item Select Menu

Change Values Select ► SubMenu

Setup Default 0 Save and Exit

The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings.

Parameter

Description

Submenu Items

Advanced CPU Control

Enter the Advanced CPU Control menu.

  • IST Configuration
  • Thermal Mode
  • CMP Support
  • Use NX capability
  • C-State support
  • Enhanced C-States Enable
  • Pop Up Support
  • Pop Down Support
  • Hard C4E
  • Bi-directional PROCHOT#
  • ACPI 3.0 T-States
  • DTS Enable
  • Thermal Trip Points Setting (Throttle On Temp.)

Platform Power Management

Enter the Platform Power Management menu.

  • PCI Clock Run
  • _CST - C4 Latency Value

ACPI S3

Enable or Disable ACPI S1/S3 Sleep State.

N/A

Wake on PME

Disable or Enable wake up when the system power is off and a PCI Power Management Enable wake up event occurs.

N/A

Wake on Modem Ring

Disable or Enable wake up when the system power is off and a modem attached to the serial port is ringing.

N/A

Parameter

Description

Submenu Items

Auto wake on S5

Disable or Enable auto wake up by date and time or at a fixed time everyday.

N/A

Quickly S4 Resume

Disable or Enable optional quick boot from S4 Resume.

N/A

This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices includes the USB diskette drives, the onboard hard disk drive and the DVD drive in the module bay.

InsydeH20 Setup Utility

Information Main Advanced Security Power Boot Exit

InsydeH20 Setup Utility

Information Main Advanced Security Power Boot Exit

2. IDE1 :

  1. USB FDD :
  2. Network Boot
  3. USB HDD :
  4. USB CDROM
Insydeh20 Setup Utility

Atheros Boot Agent

2. IDE1 :

  1. USB FDD :
  2. Network Boot
  3. USB HDD :
  4. USB CDROM

Atheros Boot Agent

Item Specific Help

Use <t > or <1 > to select a device, then press <F5> to move it down the list, or <F6> to move it up the list. Press <Esc> to escape the menu

Help Exit a

Select Select

Item Menu

Change Values Select ► SubMenu

Setup Default Save and Exit

Exit

The Exit screen allows you to save or discard any changes you made and quit the BIOS Utility.

Insydeh20 Setup Utility Rev
The table below describes the parameters in this screen.

Parameter

Description

Exit Saving Changes

Exit System Setup and save your changes to CMOS.

Exit Discarding Changes

Exit utility without saving setup data to CMOS.

Load Setup Default

Load default values for all SETUP item.

Discard Changes

Load previous values from CMOS for all SETUP items.

Save Changes

Save Setup Data to CMOS.

The BIOS flash memory update is required for the following conditions:

  • New versions of system programs
  • New features or options
  • Restore a BIOS when it becomes corrupted. Use the Phlash utility to update the system BIOS flash ROM.

NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery Diskette before you use the Phlash utility.

NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.

NOTE: Please use the AC adaptor power supply when you run the Phlash utility. If the battery pack does not contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not completely loaded.

Fellow the steps below to run the Phlash.

  1. Prepare a bootable diskette.
  2. Copy the flash utilities to the bootable diskette.
  3. Then boot the system from the bootable diskette. The flash utility has auto-execution function.

Perform the following steps to use the DOS Flash Utility:

  1. Press F2 during boot to enter the Setup Menu.
  2. Select Boot Menu to modify the boot priority order, for example, if using USB HDD to Update BIOS, move USB HDD to position 1.

Information

InsydeH20 Setup Utility

Information

InsydeH20 Setup Utility

Insydeh20 Setup Utility

2. IDE

  1. USB FDD :
  2. Network Boot I 5. USB HDD~|
  3. USB CDROM

Atheros Boot Agent

2. IDE

  1. USB FDD :
  2. Network Boot I 5. USB HDD~|
  3. USB CDROM

Atheros Boot Agent

Item Specific Help

Use <t > or <t > to select a device, then press <F5> to move it down the list, or <F6> to move it up the list. Press <Esc> to escape the menu

Help Exit a

Select Item Select Menu

Change Values Select ► SubMenu

Setup Default Save and Exit

3. Execute the FLASH.BAT batch file to update BIOS. The flash process begins as shown.

Flash Bios Extensa 5630z

4. In flash BIOS, the message Please do not remove AC Power Source displays. NOTE: If the AC power is not connected, the following message displays.

i mrisj

fill. JJJ, JJi. ijyitfi nut*

C \iU!M\,lfVnB>fUsh j<il1B023

1 ,nunvJ(mB>riashi( jutiBHza.fd /fi /B ✓be

Uamning: Mo AC power connect

C:\RQM\Jfliik

C;\flOMsjflTlB>_

tOODUff MIMETHEATE.«

Plug in the AC power to continue.

F9 F10

5. Flash is complete when the message Flash programming complete displays.

Perform the following steps to use the WinFlash Utility:

  1. Double click the WinFlash executable.
  2. Click OK to begin the update. A progress screen displays.
Insydeh20 Setup Utility Rev

3. When the process is complete, close all programs and applications and reboot the system.

The Ultimate Computer Repair Guide

The Ultimate Computer Repair Guide

Read how to maintain and repair any desktop and laptop computer. This Ebook has articles with photos and videos that show detailed step by step pc repair and maintenance procedures. There are many links to online videos that explain how you can build, maintain, speed up, clean, and repair your computer yourself. Put the money that you were going to pay the PC Tech in your own pocket.

Get My Free Ebook


Responses

  • Matthew Largo
    How to network boot through atheros boot agent?
    8 years ago
  • kodi boyle
    How to boot bios acer aspire one aod150?
    8 years ago
  • charlotte
    How to remove atheros boot agent from acer one AOD150?
    8 years ago
  • Hiewan
    How to use Acer laptop network boot agent?
    8 years ago
  • KIRK
    How hard is it to change a screen on an acer aod150?
    8 years ago

Post a comment