R

Information Main Advanced Security Power Boot Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes Change Item F9 Setup Default Select Submenu F10 Save and Exit The table below describes the parameters in this screen. The table below describes the parameters in this screen. Exit System Setup and save your changes to CMOS. Exit utility without saving setup data to CMOS. Load default values for all SETUP item. Load previous values from CMOS for all SETUP items.

Removing the Finger Print Reader

See Removing the Upper Cover on page 71. 2. Disconnect the cable as shown. 3. Disconnect the two FFC cables as shown. 3. Disconnect the two FFC cables as shown. 4. Remove the four securing screw from the Finger Print Reader board. 4. Remove the four securing screw from the Finger Print Reader board. 5. Remove the bracket from the board. 6. Remove the Finger Print Reader board from the Upper Cover.

Removing the TV Tuner module

See Removing the Battery Pack on page 46. 2. Remove the HDD2 cover. See Removing the Lower Covers on page 49. 3. Disconnect the TV Tuner cable from the module. 4. Remove the three securing screws. NOTE Some models come equipped with either a TV Tuner module or a Turbo RAM module.

Removing the Launch Board

See Removing the Upper Cover on page 71. 2. Lift up the locking latch and remove the FFC cable as shown. 3. Remove the four screws from the Launch Board. 4. Remove the Launch Board from the Upper Cover. 4. Remove the Launch Board from the Upper Cover.

HDD Not Operating Correctly

If the HDD does not operate correctly, perform the following actions one at a time to correct the problem. 1. Disconnect all external devices. 2. Run a complete virus scan using up-to-date software to ensure the computer is virus free. 3. Run the Windows Vista Startup Repair Utility a. insert the Windows Vista Operating System DVD in the ODD and restart the computer. b. When prompted, press any key to start to the operating system DVD. c. The Install Windows screen displays. Click Next. d....

Undetermined Problems

The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect, whether a short circuit is suspected, or whether the system is inoperative. Follow these procedures to isolate the failing FRU do not isolate non-defective FRU . NOTE Verify that all attached devices are supported by the computer. NOTE Verify that the power supply being used at the time of the failure is operating correctly. See Power On Issue on page 128. 2. Visually check them for...

Removing the LCD Module

Acer Aspire 4740 Display Cable

See Removing the Battery Pack on page 46. 2. Remove the SD dummy card. See Removing the Lower Covers on page 49. 3. Remove the Express dummy card. See Removing the Lower Covers on page 49. 4. Remove the Lower Covers. See Removing the Lower Covers on page 49. 5. Remove the DIMM Modules. See Removing the DIMM Modules on page 50. 6. Remove the WLAN Module. See Removing the WLAN Module on page 54. 7. Remove the HDDs. See Removing the Hard Disk Drivel Module on page 55....

Replacing the Launch Board

Replace the Launch Board on the upper cover. 2. Replace the four securing screws. 1. Replace the Launch Board on the upper cover. 2. Replace the four securing screws. 3. Insert the FFC flush with the connector and press down on the locking latch to secure. 3. Insert the FFC flush with the connector and press down on the locking latch to secure.

Replacing the ODD Module

Insert a pin in the eject hole of the ODD to eject the 2. Press the cover into the tray, bottom edge first, to ODD tray. secure. 1. Insert a pin in the eject hole of the ODD to eject the 2. Press the cover into the tray, bottom edge first, to ODD tray. secure. 3. Turn ODD Module around and secure bracket with 4. Slide Module in chassis and press until Module is two screws. flush with chassis. 3. Turn ODD Module around and secure bracket with 4. Slide Module in chassis and press until Module...

External Mouse Failure

If an external Mouse fails, perform the following actions one at a time to correct the problem. 2. If the mouse uses a wireless connection, insert new batteries and confirm there is a good connection. See the mouse user manual. 3. If the mouse uses a USB connection, try an alternate USB port. 4. Try an alternative program to verify mouse operation. Reinstall the program experiencing mouse failure. 6. Remove any recently added hardware and associated software. 7. Remove any recently added...

Lock Keys and embedded numeric keypad

The keyboard has three lock keys which you can toggle on and off. When Caps Lock is on, all alphabetic characters typed are in uppercase. When Num Lock is on, the embedded keypad is in numeric mode. The keys function as a calculator complete with the arithmetic operators , -, , and . Use this mode when you need to do a lot of numeric data entry. A better solution would be to connect an external keypad. Scroll Lock lt Fn gt lt F12 gt When Scroll Lock is on, the screen moves one line up or down...

Core POST Codes

The following table details the core POST codes and functions used in the POST. Debug Test driver for debug test PPI 1 If install debugTest driver Debug Test driver for debug test PPI 2 If install debugTest driver Debug Test driver for debug test PPI 3 If install debugTest driver Processing notify event for newly installed PPI Fail to hand off to next phase, system halt All PEIM dispatched Going to DxeIpl End of S3 resume, jump back to Waking vector Initialize the installed boot devices BIOSPSM...

Removing a Password Follow these steps

Use the t and i keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set Password box appears 2. Type the current password in the Enter Current Password field and press Enter. 3. Press Enter twice without typing anything in the Enter New Password and Confirm New Password fields. The computer then sets the Supervisor Password parameter to Clear. 4. When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility.

Internal Speaker Failure

If the internal Speakers fail, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs If sound problems are experienced, perform the following actions one at a time to correct the problem. 2. Navigate to Starts Control Panels System and Maintenance System Device Manager. Check the Device Manager to determine that The device is properly installed. There are no red Xs or yellow exclamation marks. There are no device conflicts. No hardware is listed...

Windows Keys

The keyboard has two keys that perform Windows-specific functions. The keyboard has two keys that perform Windows-specific functions. Pressed alone, this key has the same effect as clicking on the Windows Start button it launches the Start menu. It can also be used with other keys to provide a variety of functions lt gt Open or close the Start menu lt gt lt D gt Display the desktop lt gt lt E gt Open Windows Explore lt gt lt F gt Search for a file or folder lt gt lt G gt Cycle through Sidebar...

Navigating the BIOS Utility

There are six menu options Information, Main, Advanced, Security, Boot, and Exit. Follow these instructions To choose a menu, use the left and right arrow keys. To choose an item, use the up and down arrow keys. To change the value of a parameter, press F5 or F6. A plus sign indicates the item has sub-items. Press Enter to expand this item. Press Esc while you are in any of the menu options to go to the Exit menu. In any menu, you can load default settings by pressing F9. You can also press F10...

Security

The Security screen contains parameters that help safeguard and protect your computer from unauthorized Supervisor Password Is User Password Is HDD Password Is Set User Password Set Hdd Password Power on password Install or Change the password and the length of password must be less than eight words. The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings. Shows the setting of the Supervisor password Shows the setting of the...

Removing the LCD Panel

See Removing the LCD Bezel on page 90. 2. Remove the six securing screws from the LCD Module. 3. Disconnect the left and right sides of the Inverter cable. 3. Disconnect the left and right sides of the Inverter cable. 4. Disconnect the Camera Module cable as shown. 5. Grasp the panel by both ends and lift to remove.

Removing the WLAN Module

Acer 7730g Tuner Antenna

See Removing the Battery Pack on page 46. 2. Remove the HDD2 cover. See Removing the Lower Covers on page 49. 3. Remove the Turbo RAM. See Removing the TV Tuner module on page 53. 4. Disconnect the antenna cables from the WLAN board. NOTE The following is the correct cable-color to connector designation TR1 left to White, TR3 middle to Gray, and TR2 right to Black. 5. Move the cables away to avoid damaging the them, and remove the two screws on the WLAN board to release the WLAN board. 6....

Removing the Touch

See Removing the Upper Cover on page 71. 2. Remove the Speaker Module. See Removing the Speaker Module on page 79. 3. Remove the Finger Print Reader Module. See Removing the Finger Print Reader on page 76. 4. Remove the Launch Board Module. See Removing the Launch Board on page 77. 5. Remove the Launch Board Module. See Removing the Launch Board on page 77. 6. Disconnect the Touch Pad cable from the Touch Pad board. IMPORTANT The Touch Pad cannot be removed...

Removing the Bluetooth board

Bluetooth Acer Aspire 7730

See Removing the Upper Cover on page 71. 2. Remove the securing screw from the Bluetooth board. 3. Lift the Bluetooth board away from the main board and disconnect the mainboard cable. 3. Lift the Bluetooth board away from the main board and disconnect the mainboard cable. 4. Disconnect the cable from the mainboard.

FRU Field Replaceable Unit List

This chapter gives you the FRU Field Replaceable Unit listing in global configurations of Aspire 7730 7730G. Refer to this chapter whenever ordering for parts to repair or for RMA Return Merchandise Authorization . Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer...

Removing the Hard Disk Drive Module

See Removing the Battery Pack on page 46. 2. Remove the HDD2 cover. See Removing the Lower Covers on page 49. 3. Remove the two securing screws. 4. Use the pull-tab to lift up the HDD module and remove. 4. Use the pull-tab to lift up the HDD module and remove. NOTE To prevent damage to device, avoid pressing down on it or placing heavy objects on top of it. 6. Turn the HDD module upside down, and lift the HDD carrier up. 6. Turn the HDD module upside down, and lift the HDD carrier up. 7....

Removing the Modem Module

See Removing the Keyboard on page 65. 3. Using a plastic pry, partially lift up the module to expose the connector. 3. Using a plastic pry, partially lift up the module to expose the connector. 4. While holding the module, use the plastic tweezers to hold the connector and pull the module away to remove.

Advanced

The Advanced screen allows the user to configure the various advanced BIOS options. IMPORTANT Making incorrect settings to items on these pages may cause the system to malfunction. Unless you have experience adjusting these items, we recommend that you leave these settings at the default values. If making settings to items on these pages causes your system to malfunction or prevents the system from booting, open BIOS and choose Load Optimal Defaults in the Exit menu to boot up normally....

Removing the Turbo RAM module

Aspire 5050 Ram Module

See Removing the Battery Pack on page 46. 2. Remove the HDD2 cover. See Removing the Lower Covers on page 49. 3. Remove the three securing screws. 4. Remove the bracket from the module. 4. Remove the bracket from the module. NOTE Some models come equipped with either a TV Tuner module or a Turbo RAM module.

Removing the Optical Drive Module

See Removing the Battery Pack on page 46. 2. Remove the Memory cover. See Removing the Lower Covers on page 49. 3. Loosen the captive screw securing the ODD module and remove the ODD cap. 4. Carefully use a screwdriver to push the locking catch and remove the ODD module. 5. Grasp the module and pull out from the main unit. 6. Remove the two screws securing the ODD bracket and remove the ODD bracket from the optical disk drive module. 7. Insert a pin in the eject hole of the ODD to eject the...

Removing the Mainboard

4920g Motherboard

See Removing the Upper Cover on page 71. 2. Use the tweezers to lift and remove the tape strip securing the modem cable. 3. Disconnect the two cables connected to the motherboard. 4. Remove the securing screw from the Mainboard. 5. Pull the edge of the lower base outward and lift the motherboard up to remove.

Removing the Upper Cover

Acer Aspire 5610 Upside Down

See Removing the LCD Module on page 69. 2. Place the computer upside down and remove the remaining eleven screws on the bottom panel. 3. Turn the computer over and loosen the captive screw from the keyboard plate. 3. Turn the computer over and loosen the captive screw from the keyboard plate. 4. Remove the keyboard plate. If necessary, use a plastic pry to lift the plate. 5. Disconnect the five cables from the mainboard as shown. IMPORTANT When removing cables, always hold the cable by the...

Removing the LCD Brackets and FPC Cable

See Removing the LCD Panel on page 93. 2. Turn the LCD panel over to expose the rear. Grip the FPC cable and lift upward to detach the adhesive pads. 3. Remove the eight securing screws four on each side from the LCD Panel brackets. 3. Remove the eight securing screws four on each side from the LCD Panel brackets.

Touch Pad Basics with fingerprint reader

The following items show you how to use the Touch Pad with Acer Bio-Protection fingerprint reader Move your finger across the Touch Pad 2 to move the cursor. Press the left 1 and right 4 buttons located beneath the Touch Pad to perform selection and execution functions. These two buttons are similar to the left and right buttons on a mouse. Tapping on the Touch Pad is the same as clicking the left button. Use Acer Bio-Protection fingerprint reader 3 supporting Acer FingerNav 4-way control...

No Display Issue

If the Display doesn't work, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs If the POST or video doesn't display, perform the following actions one at a time to correct the problem. 1. Make sure that the internal display is selected. On this notebook model, switching between the internal display and the external display is done by pressing Fn F5. Reference Product pages for specific model procedures. 2. Make sure the computer has power by...

Information

The Information screen displays a summary of your computer hardware information. The Information screen displays a summary of your computer hardware information. Intel R Core TM 2 Duo CPU 2.40GHz F1 Help 4- Select Item ESC Exit lt gt Select Menu Enter Select Submenu F10 Save and Exit NOTE The system information is subject to different models. NOTE The system information is subject to different models. This field shows the CPU type and speed of the system. This field shows the speed of the CPU....

Replacing the Antenna MIC and Speaker Cables

IMPORTANT Ensure that all cables pass through the Mainboard and are accessible from the underside of lower cover. 1. Insert the cabling through the housing as shown. 2. Ensure that the cabling is tucked in and secured. 3. Turn the computer on its side, feed cables through to the underside. 3. Turn the computer on its side, feed cables through to the underside.

Remove Hddbios Utility

Acer Aspire 7730zg Hdd Password

This section provide you with removing HDD BIOS method If you key in wrong HDD password three times, HDD password error code displays. See the image below. To reset the HDD password, run HDD_PW.EXE as follows 3. Select one upper-case string from the list. 4. Reboot system and key in the selected string 0KJFN42 or UVEIQ96 on the HDD User Password screen. Enter Prinary faster HDD User Password If you key in the wrong Supervisor Password three times, System Disabled displays on the screen. See the...

Replacing the Upper Cover

Locate the upper cover over the lower base taking note of the screw sockets. Angle the right end of the Upper Cover in place, and insert any remaining cables through the lower base as shown. 3. Set the Upper Cover down on the lower base. 4. Replace the four securing screws on the Upper Cover. 5. Connect the five cables from the mainboard as shown. IMPORTANT When removing cables, always hold the cable by the pull-tab or by the connector. Do not hold the pull by the cable itself to prevent...

Easy Launch Buttons

Located beside the keyboard are application buttons. These buttons are called easy-launch buttons. They are WLAN, Internet, email, Bluetooth, Arcade and Acer Empowering Technology. The mail and Web browser buttons are pre-set to email and Internet programs, but can be reset by users. To set the Web browser, mail and programmable buttons, run the Acer Launch Manager. Launch Acer Empowering Technology. user-programmable Wireless communication button indicator Enables disables the wireless...

Removing the Antenna MIC and Speaker Cables

Aspire 7720 Mxm

IMPORTANT Ensure the Antenna Cables are free of any obstructions before attempting to remove. 1. Remove the WLAN Module. See Removing the WLAN Module on page 54. 2. Remove the HDD2 Module. See Removing the Hard Disk Drive2 Module on page 58. 3. Remove the MXM Module. See Removing the MXM Module on page 51. 4. Remove the Keyboard. See Removing the Keyboard on page 65. 5. Gently pull the Antenna Cables through the HDD housing. 6. Disconnect the MIC and speaker cables. IMPORTANT Use tweezers to...

Acer Aspire 7730 Factory Settings

The Main screen allows the user to set the system time and date as well as enable and disable boot option and recovery. Quick Boot Network Boot F12 Boot Menu D2D Recovery SATA Mode Enabled Enabled Disabled Enabled ACHI Help T Select Item F5 F6 Change Item F9 Setup Default Exit lt gt Select Menu Enter Select Submenu F10Save and Exit NOTE The screen above is for your reference only. Actual values may differ. The table below describes the parameters in this screen. Settings in boldface are the...

External Modules Disassembly Flowchart

The flowchart below gives you a graphic representation on the entire disassembly sequence and instructs you on the components that need to be removed during servicing. For example, if you want to remove the main board, you must first remove the keyboard, then disassemble the inside assembly frame in that order.

Removing the Express Card Module

Aspire 7730 Express Card

See Removing the Upper Cover on page 71. 2. Remove the two securing screws. IMPORTANT Do not grasp the cable itself to prevent fraying. IMPORTANT Do not grasp the cable itself to prevent fraying. 3. Disconnect the cable connecting the ExpressCard module. 3. Disconnect the cable connecting the ExpressCard module.

BIOS Setup Utility

The BIOS Setup Utility is a hardware configuration program built into your computer's BIOS Basic Input Output System . Your computer is already properly configured and optimized, and you do not need to run this utility. However, if you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4 Troubleshooting when problem arises. To activate the BIOS Utility, press F2 during POST when Press lt F2 gt to enter Setup message is prompted on the bottom of screen ....

Common Problems

Use the following procedure as a guide for computer problems. NOTE The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or modified options can give false errors and invalid system responses. 1. Obtain the failing symptoms in as much detail as possible. 2. Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating the same operation. 3. Use the following table with the verified symptom to determine which...

Removing the Subwoofer Module

Subwoofer Module

See Removing the Upper Cover on page 71. 2. Remove the four securing screws from the Subwoofer Module. 3. Grasp the cable by the end and guide it out of its housing as shown in the following images. 3. Grasp the cable by the end and guide it out of its housing as shown in the following images. IMPORTANT The housing guides are hooked to hold the cable in place. Do not pull the cable to remove it or damage can occur. 4. Grasp the Subwoofer Module and lift it up to remove.

Replacing the Hard Disk Drive Module

Acer Aspire Extensa Winchester Change

Replace the connector on the HDD. 2. Place the HDD in the HDD carrier. 1. Replace the connector on the HDD. 2. Place the HDD in the HDD carrier. 3. Replace the four screws two each side to secure 4. Insert the HDD, left side first, and push down to the carrier. locate the interface correctly. 3. Replace the four screws two each side to secure 4. Insert the HDD, left side first, and push down to the carrier. locate the interface correctly.

BIOS Recovery by Crisis Disk

BIOS Recovery Boot Block is a special block of BIOS. It is used to boot up the system with minimum BIOS initialization. Users can enable this feature to restore the BIOS firmware to a successful one once the previous BIOS flashing process failed. The system provides a function hotkey Fn Esc, for enable BIOS Recovery process when system is powered on during BIOS POST. To use this function, it is strongly recommended to have the AC adapter and Battery present. If this function is enabled, the...

LCD Module Reassembly Procedure

Align the LCD brackets with the eight screw holes four on each side on the LCD Panel as shown. 1. Align the LCD brackets with the eight screw holes four on each side on the LCD Panel as shown. 2. Secure the LCD brackets to the LCD panel. 2. Secure the LCD brackets to the LCD panel. 3. Turn the panel over. Insert the LCD Panel cable into the LCD Panel as shown. 4. Align the LCD Panel cable as shown and press down to secure in place. 5. Take care to insert the top of the panel fist and then 6....

Removing the Switch Cover

Open Acer 7730

CAUTION Using tools to remove the Switch Cover may cause damage to the outer casing. It is recommended that only fingers are used to remove the Switch Cover. 1. Remove the Battery Pack. See Removing the Battery Pack on page 46. 2. Locate and remove the nine securing screws as shown. 3. Turn the computer over and open the LCD module fully to expose the Switch Cover. 4. Lift the Switch Cover up and away.

Acer Grid Vista dualdisplay compatible

NOTE This feature is only available on certain models. To enable the dual monitor feature of the notebook, first ensure that the second monitor is connected, then select Start, Control Panel, Display and click on Settings. Select the secondary monitor 2 icon in the display box and then click the check box Extend my windows desktop onto this monitor. Finally, click Apply to confirm the new settings and click OK to complete the process. Acer GridVista is a handy utility that offers four...

Replacing the Finger Print Reader

Remove the Finger Print Reader board from the Upper Cover. 2. Remove the bracket from the board. 3. Replace the four securing screw on the Finger Print Reader board. NOTE Move back the cabling to allow for easier access to the screw sockets. 4. Connect the two FFC cables as shown.

Acer Boot Menu Aspire 7730

Network Diagrams

This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices includes the USB diskette drives, the onboard hard disk drive and the DVD drive in the module bay. Information Main Advanced Security Power 2. IDE1 Slimtype DVD A DS8A2S 3 . USB FDD 4. Network Boot Realtek Boot Agent Item Specific Help Use lt T gt or to select a device, then press lt F5 gt to move it down the list, or lt F6 gt to move it up the list. Press lt Esc gt to escape the menu

Disassembly Requirements

To disassemble the computer, you need the following tools Wrist grounding strap and conductive mat for preventing electrostatic discharge NOTE The screws for the different components vary in size. During the disassembly process, group the screws with the corresponding components to avoid mismatch when putting back the components. Before proceeding with the disassembly procedure, make sure that you do the following 1. Turn off the power to the system and all peripherals. 2. Unplug the AC adapter...

Removing the LCD Bezel

See Removing the LCD Module on page 69. 2. Remove the six rubber covers and screws. 3. Starting from the inside edges, pry the inside of the bezel upwards from the panel. Continue moving left until the bezel is removed. If necessary, use a plastic pry to release the corners of the bezel. 4. Lift up the bezel and remove it from the LCD Module.

Disassembly Process

The disassembly process is divided into the following stages External module disassembly The flowcharts provided in the succeeding disassembly sections illustrate the entire disassembly sequence. Observe the order of the sequence to avoid damage to any of the hardware components. For example, if you want to remove the main board, you must first remove the keyboard, then disassemble the inside assembly frame in that order.

Removing the Switch Board

Button Board Aspire 9410

See Removing the Switch Cover on page 63. 2. Remove the two securing screws from the Switch Board. 3. Disconnect the Switch Board to Ekey board FFC cable as shown. 3. Disconnect the Switch Board to Ekey board FFC cable as shown. 4. Use the tweezers to secure the cable in place, then remove the Switch Board away from the top cover.

BIOS Flash Utility

The BIOS flash memory update is required for the following conditions New versions of system programs Restore a BIOS when it becomes corrupted. Use the Phlash utility to update the system BIOS flash ROM. NOTE If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery Diskette before you use the Phlash utility. NOTE Do not install memory-related drivers XMS, EMS, DPMI when you use the Phlash. NOTE Please use the AC adaptor power supply when you run the Phlash...

Clearing Password Check and BIOS Recovery

This section provide you the standard operating procedures of clearing password and BIOS recovery for Aspire 7730 7730G. Aspire 7730 7730G provide one Hardware Open Gap on main board for clearing password check, and one Hotkey for enabling BIOS Recovery. Clearing Password Check Hardware Open Gap Description Steps for Clearing BIOS Password Check If users set BIOS Password Supervisor Password and or User Password for a security reason, BIOS will ask the password during systems POST or when...

Hot Keys

The computer employs hotkeys or key combinations to access most of the computer's controls like screen brightness, volume output and the BIOS utility. To activate hot keys, press and hold the lt Fn gt key before pressing the other key in the hotkey combination. Launches Acer eSettings Management in Acer Empowering Technology. Launches Acer ePower Management in Acer Empowering Technology. Switches display output between the display screen, external monitor if connected and both. Turns the...

Insydeh20 Setup Utility Acer Aspire

Nsydeh20 Setup Utility Ayarlar

The Power screen allows the user to configure various CPU and power management options and device wakeup behavior. The table below describes the items, menus, and submenus in this screen. Settings in boldface are the default and suggested parameter settings. Enter the Advanced CPU Control menu. Thermal Trip Points Setting Fan Enter the Platform Power Management menu. Enable or Disable ACPI S1 S3 Sleep State Enable or Disable wake up when the system power is off and a PCI Power Management Enable...

Hardware Specifications and Configurations

Supports Intel architecture with Dynamic execution. On-die, primary 32-kB instruction cache and 32-kB write-back data On-die, up to 6MB second level shared cache with advanced transfer cache architecture. Streaming SIMD Extensions 2 SSE2 ,Streaming SIMD Extensions 3 SSE3 Supplemental streaming SIMD extensions 3 SSSE3 1066MHz source-synchronous front side bus FSB Advanced power management features including Enhanced Intel SpeedStep Technology and dynamic FSB frequency switching. Execute disable...

Removing the CPU Fan Module

Aspire Fan Connector

See Removing the Battery Pack on page 46. 2. Remove the Mainboard. See Removing the Mainboard on page 85. 3. Turn the Mainboard right side up, and place it on a clean surface. 4. Using tweezers, grip the cable connector and disconnect the Fan cable from the Mainboard. IMPORTANT Do not grip the cable itself to prevent stripping. 5. Loosen the three captive screws from the heatsink. 6. Lift the cover to expose the single securing screw. Remove the screw. 7. Lift the Fan module clear of the...

Lower Cover

Dvb Mini Tuner Card A310 Conn Ada

ADAPTER 65W 3PIN DELTA SADP-65KB DFA ADAPTER LITE-ON 90W 19V BLUE PA-1900-24AR LED LF ADAPTER HIPRO 90W 19V BLUE HP-OL093B13P LED LF LEVEL 4 Battery SONY AS-2007B Li-Ion 3S2P SONY 6 cell 4400mAh Main COMMON Normal Type Battery PANASONIC AS-2007B Li-Ion 3S2P PANASONIC 6 cell 4400mAh Main COMMON PSS Battery SANYO AS-2007B Li-Ion 3S2P SANYO 6 cell 4400mAh Main COMMON Normal Type Battery SIMPLO AS-2007B Li-Ion 3S2P PANASONIC 6 cell 4400mAh Main COMMON PSS Battery PANASONIC AS-2007B Li-Ion 4S2P...

Replacing the Mainboard

Aspire 5920g Motherboard

Pull the edge of the lower base outward and insert 2. Replace the securing screw on the Mainboard. the motherboard in the lower base. 3. Connect the two cables connected to the motherboard. 3. Connect the two cables connected to the motherboard. 4. Replace the adhesive strip securing the modem cable. 4. Replace the adhesive strip securing the modem cable.