Continue

The password setting is complete after the user presses Enter. If the current password entered does not match the actual current password, the screen will show you the Setup Warning. If the new password and confirm new password strings do not match, the screen displays the following message.

Removing the Power Save Board

See Removing the LCD Module on page 68. 2. Disconnect the Power Save Board from the Function Board by lifting the FFC lock and removing the FFC as shown. 3. Remove the two screws securing the Power Save Board to the Switch Cover as shown. 4. Remove the Power Save Board from the Switch Cover.

Lock Keys and embedded numeric keypad

The keyboard has three lock keys which you can toggle on and off. Fll M FTTSi Piu . fell Sytt, ftrJ When Caps Lock is on, all alphabetic characters typed are in uppercase. When Num Lock is on, the embedded keypad is in numeric mode. The keys function as a calculator (complete with the arithmetic operators +, -, *, and ). Use this mode when you need to do a lot of numeric data entry. A better solution would be to connect an external keypad. Scroll Lock < Fn> + < F12> When Scroll Lock is...

Replacing the Multifunction Board

Insert the Multifunction Board into the casing, ensuring that the USB Port is accessible through the case. 2. Run the cable along the casing and insert it into the FFC connector. 1. Insert the Multifunction Board into the casing, ensuring that the USB Port is accessible through the case. 3. Lock the connector and press down on the FFC cable to secure it on the casing. Ensure the locating pins is correctly seated and replace the single securing screw.

Removing the LCD Module

See Removing the WLAN Module on page 52. 2. See Removing the Keyboard on page 67. 3. Turn the computer over. Remove the two securing screws as shown. 4. Starting at the LCD module, completely remove the Antenna cable from the cable channel. 4. Starting at the LCD module, completely remove the Antenna cable from the cable channel. Disconnect the LCD cables from the Mainboard and remove the cable from the cable channel as shown Disconnect the LCD cables from the Mainboard and remove the cable...

Replacing the Upper Cover

5739g Cover

WARNING Care must be taken when replacing the Upper Cover to prevent damage or stress to the surface. 5. Ease the lower casing outward to clear the securing clips and pry apart the right side as shown. Lift the rear edge of the Upper Base upward. 7. Reconnect the four FFC cables to the mainboard. 8. Replace the 13 securing screws on the top panel. 9. Turn the computer over. Replace the nine screws on the bottom panel.

Acer Aspire 5739g Quieter

The Main screen allows the user to set the system time and date as well as enable and disable boot option and recovery. Phoenix SecureCode tm Setup Utility Help Select Item Exit 9 Select Menu Change Values KQ Setup Default Select SubMenu BFM Save and Exit NOTE The screen above is for your reference only. Actual values may differ. The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings. Sets the system time. The hours are...

Navigating the BIOS Utility

There are six menu options Information, Main, Advanced, Security, Power, Boot, and Exit. Follow these instructions To choose a menu, use the left and right arrow keys. To choose an item, use the up and down arrow keys. To change the value of a parameter, press F5 or F6. A plus sign indicates the item has sub-items. Press Enter to expand this item. Press Esc while you are in any of the menu options to go to the Exit menu. In any menu, you can load default settings by pressing F9. You can also...

Intermittent Problems

Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a recurring problem exists. When analyzing an intermittent problem, do the following 1. Run the advanced diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any FRU. 3. If any error is detected,...

Removing the Thermal Module

See Removing the Mainboard on page 80. 2. Turn the Mainboard over and place on a clean surface. 3. Hold the fan cable connector and lift to disconnect from the mainboard. 4. Loosen the three captive screws from the Thermal Module CPU heat sink in reverse numerical order, from 3 to 1. 5. Remove the four screws from the Thermal Module. WARNING To prevent damage to the Thermal Module or the CPU, hold and lift the Thermal Module by lifting both ends up and away at the same time. 6. Hold the...

Disassembly Process

The disassembly process is divided into the following stages External module disassembly The flowcharts provided in the succeeding disassembly sections illustrate the entire disassembly sequence. Observe the order of the sequence to avoid damage to any of the hardware components. For example, if you want to remove the main board, you must first remove the keyboard, then disassemble the inside assembly frame in that order.

Enter New Password Confirm New Password

Type a password in the Enter New Password field. The password length can not exceeds 8 alphanumeric characters A-Z, a-z, 0-9, not case sensitive . Retype the password in the Confirm New Password field. IMPORTANT Be very careful when typing your password because the characters do not appear on the screen. 3. Press Enter. After setting the password, the computer sets the User Password parameter to Set. 4. If desired, you can opt to enable the Password on boot parameter. 5. When you are done,...

Front View

Web camera for video communication only for certain models . Internal Microphone for sound recording Also called Liquid-Crystal Display LCD , displays computer output Configuration may vary by models . Indicates when the hard disk drive is active. Lights up when Num Lock is activated. Lights up when Caps Lock is activated. Touch sensitive controls for Acer Arcade, volume up down and media play pause, stop, previous, next with mute and hold keys For entering data into your computer....

Information

The Information screen displays a summary of your computer hardware information. Phoenix SecureCore tm Setup Utility Intel R Core TM 2 Duo CPU P6570 2.10GHz Help Select Item Hgj B Change Values RB Setup Default Exit jSpjppt Menu jEfflfl Select SubMenu JJ Save and Exit Help Select Item Hgj B Change Values RB Setup Default Exit jSpjppt Menu jEfflfl Select SubMenu JJ Save and Exit NOTE The system information is subject to different models. This field shows the CPU type of the system. This field...

Internal Speaker Failure

If the internal Speakers fail, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs If sound problems are experienced, perform the following actions one at a time to correct the problem. 2. Navigate to Starts Control Panels System and Maintenance System Device Manager. Check the Device Manager to determine that The device is properly installed. There are no red Xs or yellow exclamation marks. There are no device conflicts. No hardware is listed...

Replacing the DIMM Modules

NOTE To replace DIMM Module 2, first remove DIMM Module 1. In this procedure, only DIMM Module 1 is 1. Insert the DIMM Module flush with the connector and press down to lock in place. 1. Insert the WLAN board into the WLAN socket. 2. Replace the single screw to secure the module. 1. Insert the WLAN board into the WLAN socket. 2. Replace the single screw to secure the module. 3. Connect the three antenna cables to the module. NOTE The White cable goes to the upper terminal TR 1 , the black cable...

Replacing the ODD Module

Align the ODD Bezel as shown and press it into place. 2. Align the ODD Bracket as shown and replace the securing screws. 2. Align the ODD Bracket as shown and replace the securing screws. 3. Push the ODD Module into the chassis as shown 4. Replace the securing screw. until the bezel is flush with the casing.

Removing the LCD Bezel

See Removing the LCD Module on page 68. 3. Starting at the centre of the top edge, pry the inside of the bezel away from the screen. Work round the edges to pry the bezel away from the screen as shown. 4. Lift the bezel away from the panel and place it face down above the panel as shown. 4. Lift the bezel away from the panel and place it face down above the panel as shown. IMPORTANT The microphone cable still connects the bezel to the panel, take care not to pull the bezel away from the...

Left View

Connects to an Ethernet 10 100 1000-based network. Connects to a display device e.g. external monitor, LCD projector . Supports high definition digital video connections. Connect to USB 2.0 devices e.g. USB mouse, USB camera Accepts audio line-in devices e.g., audio CD player, stereo walkman, mp3 player Accepts inputs from external microphones. Headphones speaker line-out jack with S PDIF support Connects to audio line-out devices e.g., speakers, headphones .

FRU Field Replaceable Unit List

This chapter gives you the FRU Field Replaceable Unit listing in global configurations of the Aspire 5739. Refer to this chapter whenever ordering for parts to repair or for RMA Return Merchandise Authorization . Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer...

Acer Grid Vista dualdisplay compatible

NOTE This feature is only available on certain models. To enable the dual monitor feature of the notebook, first ensure that the second monitor is connected, then select Start, Control Panel, Display and click on Settings. Select the secondary monitor 2 icon in the display box and then click the check box Extend my windows desktop onto this monitor. Finally, click Apply to confirm the new settings and click OK to complete the process. Acer GridVista is a handy utility that offers four...

Undetermined Problems

The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect, whether a short circuit is suspected, or whether the system is inoperative. Follow these procedures to isolate the failing FRU do not isolate non-defective FRU . NOTE Verify that all attached devices are supported by the computer. NOTE Verify that the power supply being used at the time of the failure is operating correctly. See Power On Issue on page 134. 2. Visually check them for...

Replacing the LCD Panel

Align the LCD brackets with the six screw holes three on each side on the LCD Panel as shown. 2. Replace the six securing screws in numeric order, from 1 to 3. 3. Turn the panel over. Insert the LCD Panel cable into the LCD Panel as shown 1 . Secure the cable by replacing the securing strip 2 . 4. Run the LCD cable as shown and press down along the length of the cable to secure it in place. Insert the LCD panel into the casing back edge first as shown. Ensure that the four locating pins are...

Replacing the Switch Cover

CAUTION Using tools to remove the Switch Cover may cause damage to the outer casing. It is recommended that only fingers are used to remove the Switch Cover. 1. See Removing the Battery Pack on page 49. 2. See Removing the Hinge Covers on page 63. 3. Place the switch board on the keyboard. 4. Connect the power board to the main unit by inserting the FFC and closing the FFC lock as shown. 5. Connect the function board to the main unit by inserting the FFC and closing the FFC lock as shown. 6....

Removing the Switch Cover

Aspire 5739g Bottom

CAUTION Using tools to remove the Switch Cover may cause damage to the outer casing. It is recommended that only fingers are used to remove the Switch Cover. 1. See Removing the Battery Pack on page 49. 2. See Removing the Hinge Covers on page 63. 3. Locate and remove the six securing screws on the bottom of the computer. 4. Turn the computer over and open the LCD module to expose the Switch Cover. IMPORTANT The LCD module does not fully extend. Damage will occur if you attempt to extend the...

Removing the Keyboard

See Removing the Switch Cover on page 63. 2. Pull up on the center rear of the keyboard until the Keyboard snaps free of the securing tabs on both sides of the Keyboard. IMPORTANT The keyboard is still attached to the Mainboard FFC IMPORTANT The keyboard is still attached to the Mainboard FFC 4. Unlock the connector and pull the FFC to remove it from the Mainboard. 4. Unlock the connector and pull the FFC to remove it from the Mainboard. 5. Remove the keyboard from the chassis.

Removing the Power Switch Board

See Removing the LCD Module on page 68. 2. Remove the three screws securing the Power Save Board to the Switch Cover as shown. 3. Remove the power board by sliding it out from the securing tab as shown. 3. Remove the power board by sliding it out from the securing tab as shown.

Removing the Finger Print Reader

NOTE Only the Discrete SKU supports Finger Print Reader technology. 1. See Removing the Upper Base on page 72. 2. Lift the FFC locking latch, as shown, to disengage the cable and disconnect the main board FFC. 3. Open the FFC locking latch as shown and remove the FFC. 4. Remove the three securing screws on the bracket. 5. Pull the fingerprint reader out from under the securing brackets as shown.

Replacing the Modem Module

Connect the modem cable as shown. 2. Replace the Modem Module on the Mainboard. 1. Connect the modem cable as shown. 2. Replace the Modem Module on the Mainboard. 3. Align the screw sockets and replace the two screws. 3. Align the screw sockets and replace the two screws.

Replacing the Mainboard

Aspire 5739g Mainboard

Lift the mainboard right side first to remove from the base. 2. Replace the single securing screw. 3. Grasp the RJ-11 cable and insert it into the Mainboard as shown. 3. Grasp the RJ-11 cable and insert it into the Mainboard as shown. 5. Connect the cable to the Bluetooth board. 6. Connect the FFC connecting to the Multifunction board.

Removing the CPU

Acer 4736 Dismantle

See Removing the Graphics Card on page 59. NOTE With the graphics card removed, the GPU thermal pads are exposed. Do not allow any object to come into contact with the thermal pads as their performance will be seriously degraded if they are damaged. Replace the thermal pads if any object comes into contact with them. 2. Unscrew the three securing screws of the CPU heat sink in the indicated order 3, 2, 1. 3. Using a flat screwdriver, turn the CPU socket latch counter-clockwise 180 to release...

BIOS Setup Utility

The BIOS Setup Utility is a hardware configuration program built into your computer's BIOS Basic Input Output System . Your computer is already properly configured and optimized, and you do not need to run this utility. However, if you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4 Troubleshooting if a problem arises. To activate the BIOS Utility, press F2 during POST when Press lt F2 gt to enter Setup message is prompted on the bottom of screen ....

Replacing the Hinge Covers

IMPORTANT The left and right Hinge Covers are shaped differently and marked L and R on the inside. Ensure that the correct cover is used during reassembly. 1. Align the Hinge Covers screw hole side up and slide them onto the hinge assemblies. 2. Replace the two securing screws and caps.

Random Loss of BIOS Settings

If the computer is experiencing intermittent loss of BIOS information, perform the following actions one at a time to correct the problem. 1. If the computer is more than one year old, replace the CMOS battery. 2. Run a complete virus scan using up-to-date software to ensure the computer is virus free. 3. If the computer is experiencing HDD or ODD BIOS information loss, disconnect and reconnect the power and data cables between devices. If the BIOS settings are still lost, replace the cables....

Replacing the Speaker Modules

Place the speaker module into the lower base as shown 6. Push the subwoofer module onto the securing tabs as shown. IMPORTANT Do not hold the subwoofer by the edges as contact with the speakers can damage the unit. 7. Replace the three screws to secure the Speaker Modules. 8. Replace the speaker wire into the channel as shown. 8. Replace the speaker wire into the channel as shown.

Remove Hddbios Password Utilities

Primary Master Hdd User Password

To reset a hard drive or BIOS password you require an additional PC. The utilities run on a DOS prompt on the second machine. This section provides instructions on how to remove a HDD password. If you enter the wrong hard drive password three times, the system reports the following error code Hdd password error code Il 15494 II To reset the HDD password, run HDD_PW.EXE on a second machine as follows 1. At a command prompt, type hdd_pw 15494 0 3. Write down one of the two strings in this...

Hot Keys

The computer employs hotkeys or key combinations to access most of the computer's controls like screen brightness and volume output. To activate hotkeys, press and hold the lt Fn gt key before pressing the other key in the hotkey combination. Display the System Properties dialog box. Enables disables the Bluetooth function. only for certain models Switches display output between the display screen, external monitor if connected and both. Turns the display screen backlight off to save power....

Replacing the CPU Alternate Procedure

5739g Sockel Cpu

IMPORTANT The CPU has a Pin1 locator that must be positioned corresponding to the marker on the CPU socket NOTE Only use this procedure if you removed the thermal unit according to the instuctions given in Removing the CPU Alternate Procedure on page 84. IMPORTANT Ensure all thermal pads are in place before replacing the Thermal Module. The following thermal pads are approved for use The following thermal compounds are approved for use Eapus XR-PE 1. Remove all traces of thermal grease or pad...

HDD Not Operating Correctly

If the HDD does not operate correctly, perform the following actions one at a time to correct the problem. 1. Disconnect all external devices. 2. Run a complete virus scan using up-to-date software to ensure the computer is virus free. 3. Run the Windows Vista Startup Repair Utility a. insert the Windows Vista Operating System DVD in the ODD and restart the computer. b. When prompted, press any key to start to the operating system DVD. c. The Install Windows screen displays. Click Next. d....

Replacing the Thermal Module

Acer Aspire 5738zg Cleaning

IMPORTANT Ensure all thermal pads are in place before replacing the Thermal Module. The following thermal pads are approved for use The following thermal compounds are approved for use 1. Remove all traces of thermal grease or pad adhesive from the Graphics Card and CPU using a lint-free cloth or cotton swab and Isopropyl Alcohol, Acetone, or other approved cleaning agent. 2. Apply a small amount of thermal grease or the supplied thermal pad to the center of the heat sink and the indicated...

Replacing the Graphics Card

How Insert Graphic Card

The following thermal pads are approved for use The following thermal compounds are approved for use Eapus XR-PE 2. Remove all traces of thermal grease or pad adhesive from the heat sink using a lint-free cloth or cotton swab and Isopropyl Alcohol, Acetone, or other approved cleaning agent. 3. Apply a small amount of thermal grease or the supplied thermal pads to the locations indicated below. There is no need to spread grease manually, the force used during the installation of the Thermal...

Common Problems

Use the following procedure as a guide for computer problems. NOTE The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or modified options can give false errors and invalid system responses. 1. Obtain the failing symptoms in as much detail as possible. 2. Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating the same operation. 3. Use the following table with the verified symptom to determine which...

Hardware Specifications and Configurations

INTEL Penryn processor on 45-nanometer process technology Dual-core processor for mobile with enhanced performance Supports Intel architecture with IntelR Wide Dynamic Execution Supports L1 cache-to-cache C2C transfer On-die, primary 32-kB instruction cache and 32-kB write-back data cache in each core The Penryn processor in XE, SV and LV have an On-die, up to 6-MB second-level shared cache with Advanced Transfer Cache architecture The Penryn processor in ULV have an On-die, up to 3-MB...

Replacing the CPU

IMPORTANT The CPU has a Pin1 locator that must be positioned corresponding to the marker on the CPU socket The following thermal pads are approved for use The following thermal compounds are approved for use 1. Raise the heat sink and hold it in a raised posotion. 2. Remove all traces of thermal grease or pad adhesive from the heat sink using a lint-free cloth or cotton swab and Isopropyl Alcohol, Acetone, or other approved cleaning agent. 3. Place the CPU into the socket. Take note of the Pin...

Replacing the Hard Disk Drive Module

Place the HDD carrier on the HDD. 2. Replace the two securing screws. 1. Place the HDD carrier on the HDD. 2. Replace the two securing screws. 3. Place the HDD Module in the HDD bay as shown and slide it in the direction of the arrow to connect the interface. 4. Replace the single screw to secure the hard disk bracket to the Lower Cover. 4. Replace the single screw to secure the hard disk bracket to the Lower Cover.

Replacing the LCD Module

Acer 5739g Main Board

Carefully place the LCD Module into the chassis, making sure to align the mounting pins on the LCD brackets with the well son the Lower Cover. 11. Replace the two securing screws for the left LCD hinge. 12. Replace the two securing screws for the right LCD hinge. 13. Connect the LCD cable to the Mainboard and insert the cable into the cable channel as shown. 13. Connect the LCD cable to the Mainboard and insert the cable into the cable channel as shown. 14. Rest the computer on its side...

Using the Flash Utility to Update the BIOS

Acer Aspire 5332 Boot Priority

Follow the steps below to run the Flash16 Utility. 1. Prepare a bootable diskette. 2. Copy the flash utilities to the bootable diskette. 3. Boot the system from the bootable diskette. 4. Run Phlash16.exe z06_3106.wph mode 3 x. After flashing the BIOS the system will restart. 5. During POST, press F2 to enter into the BIOS setup screen. 6. Navigate to the Exit page, choose Load Setup Defaults then press ENTER. 7. When a Setup Confirmation appears, choose 'Yes'. The system will restart with the...

Removing the LCD Brackets and FPC Cable

See Removing the LCD Panel on page 91. 2. Remove the four securing screws two on each side from the LCD Panel brackets. 3. Turn the LCD Panel over on a clean surface. 4. Remove the cable from the panel as shown 2 . 5. Lift the cable as shown to detach the adhesive. 5. Lift the cable as shown to detach the adhesive. 6. Grip the adhesive strip covering the LCD cable connector and pull it back 1 . 7. Remove the LCD brackets by pulling them away from the LCD Panel.

External Modules Disassembly Flowchart

The flowchart below gives you a graphic representation on the entire disassembly sequence and instructs you on the components that need to be removed during servicing. For example, if you want to remove the main board, you must first remove the keyboard, then disassemble the inside assembly frame in that order.

Disassembly Requirements

To disassemble the computer, you need the following tools Wrist grounding strap and conductive mat for preventing electrostatic discharge NOTE The screws for the different components vary in size. During the disassembly process, group the screws with the corresponding components to avoid mismatch when putting back the components.

Enter Current Password Enter New Password Confirm New Password

Type the current password in the Enter Current Password field and press Enter. 3. Press Enter twice without typing anything in the Enter New Password and Confirm New Password fields. The computer then sets the Supervisor Password parameter to Clear. 4. When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility. 1. Use the t and i keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set Password box appears. Enter Current...

Clearing Password Check and BIOS Recovery

Gap Acer Aspire 5930g

This section provide you the standard operating procedures of clearing password and BIOS recovery for Aspire 5739. Aspire 5739 provides one Hardware Open Gap on main board for clearing password check, and one Hotkey for enabling BIOS Recovery. Clearing Password Check Hardware Open Gap Description Steps for Clearing BIOS Password Check If users set a BIOS Password Supervisor Password and or User Password for security reasons, the BIOS will prompt for a password during system POST or when systems...

Security

May Acer 4710 Phoenix

The Security screen contains parameters that help safeguard and protect your computer from unauthorized use. Phoenix SecureCore tm Setup Utility Phoenix SecureCore tm Setup Utility The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings. Shows the setting of the Supervisor password Shows the setting of the User password. Shows the setting of the HDD password. Press Enter to set the supervisor password. When set, this...

Acer 5739g Bios Changelog

Acer Aspire 5739g Bios Kleme

This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices includes USB drives, the onboard hard disk drive and the DVD drive in the module bay. Phoenix SecureCore tm Setup Utility Keys used to view or configure devices Up and Down arrows select a device. lt gt and lt - gt moves the device up or down. lt f gt and lt r gt specifies the device fixed or removable. lt x gt exclude or include the device to boot. lt Shift 1 gt enables or disables a...

Aspire FRU List

Adapter DELTA 65W 19V 1.7x5.5x11 Yellow ADP-65JH DB A, LV5 LED LF Adapter DELTA 90W 19V 1.7x5.5x11 Blue ADP-90CD DB A, LV5 LED LF Adapter LITE-ON 90W 19V 1.7x5.5x11 Blue PA-1900-34AR, LV5 LED LF Adapter HIPRO 90W 19V 1.7x5.5x11 Blue HP-A0904A3 B1LF, LV5 LED LF Adapter LITE-ON 65W 19V 1.7x5.5x11 Yellow PA-1650-22AC LV5 LED LF Adapter HIPRO 65W 19V 1.7x5.5x11 Yellow HP-A0652R3B 1LF, LV5 LED LF Battery SANYO AS-2007B Li-Ion 3S2P SANYO 6 cell 4400mAh Main COMMON Normal Type Battery PANASONIC...

Internal Microphone Failure

If the internal Microphone fails, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs If internal or external Microphones do no operate correctly, perform the following actions one at a time to correct the problem. 1. Check that the microphone is enabled. Navigate to Starts Control Panels Hardware and Sounds Sound and select the Recording tab. 2. Right-click on the Recording tab and select Show Disabled Devices clear by default . 3. The...

Miscellaneous Utilities

Boot Sequence Selector allows the boot order to be changed without accessing the BIOS. To use Boot Sequence Selector, perform the following steps 2. Execute BS.exe to display the usage screen. Boot Sequence Selecter Version 0.G3 Create by Rockwell Chuang 10 01 2005. I Floppy 1 gt HardDiskl gt CD-ROM 1 gt f LRN J HnrrlDiski CD-RDM 1 gt I ION 1 I Floppy 1 CD-ROH 1 gt HardDiskl gt 1 LHH 1 gt Floppy 1 gt I Floppy 1 gt HardDiskl gt CD-ROM 1 Select the desired boot sequence by entering the...

Replacing the LCD Bezel

5739g Lcd Cover

Place the Bezel on the casing bottom edge first 2. Press down the sides of the bezel, working toward and press in the areas marked to snap it into place. the top edge. 3. Press down the top edge to complete the process. IMPORTANT Ensure there are no gaps between the LCD Cover and the Bezel. 4. Replace the six securing screws and screw caps on the LCD bezel. IMPORTANT Four of the screw caps are rubber pads. Be sure to replace them along the top edge of the LCD panel.

Removing the Hinge Covers

Aspire 5739g Inside

See Removing the Battery Pack on page 49. 2. Remove the two screw caps and screws from the Hinge Covers. 3. Slide the covers off the hinges in the direction of the arrows. IMPORTANT The left and right Hinge Covers are shaped differently and marked L and R on the inside. Ensure that the correct cover is used during reassembly.