Setup Defaults Save and Exit

The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings.

Parameter

Description

Option

Supervisor Password Is

Shows the setting of the Supervisor password

Clear or Set

User Password Is

Shows the setting of the user password.

Clear or Set

HDD 0 Password Is

Shows the setting of the hard disk password.

Clear or Set

Set Supervisor Password

Press Enter to set the supervisor password. When set, this password protects the BIOS Setup Utility from unauthorized access. The user can not either enter the Setup menu nor change the value of parameters.

N/A

Set User Password

Press Enter to set the user password. When user password is set, this password protects the BIOS Setup Utility from unauthorized access. The user can enter Setup menu only and does not have right to change the value of parameters.

N/A

Set HDD 0 Password

Enter HDD 0 Password.

N/A

Password on Boot

Defines whether a password is required or not while the events defined in this group happened. The following sub-options are all requires the Supervisor password for changes and should be grayed out if the user password was used to enter setup.

Disabled or

Enabled

NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don't forget your password. If you forget your password, you may have to return your notebook computer to your dealer to reset it.

Setting a Password

Follow these steps as you set the user or the supervisor password:

1. Use the t and i keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set Supervisor Password box appears:

Set Supervisor Password Enter New Password [ Confirm New Password [

2. Type a password in the "Enter New Password" field. The password length can not exceeds 8 alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the "Confirm New Password" field.

IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen.

  1. Press Enter. After setting the password, the computer sets the User Password parameter to "Set".
  2. If desired, you can opt to enable the Password on boot parameter.
  3. When you are done, press F10 to save the changes and exit the BIOS Setup Utility.

Removing a Password

Follow these steps:

1. Use the t and i keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set Password box appears:

Set Supervisor Password

Enter current p as swo rd [

]

Enter New Password f

]

Confirm New Password [

]

  1. Type the current password in the Enter Current Password field and press Enter.
  2. Press Enter twice without typing anything in the Enter New Password and Confirm New Password fields. The computer then sets the Supervisor Password parameter to "Clear".
  3. When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility.

Changing a Password

1. Use the t and i keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set Password box appears.

Set Supervisor Password

Enter current p as s wo rd [

]

Enter New Password [

]

Confirm New Password [

]

  1. Type the current password in the Enter Current Password field and press Enter.
  2. Type a password in the Enter New Password field. Retype the password in the Confirm New Password field.
  3. Press Enter. After setting the password, the computer sets the User Password parameter to "Set".
  4. If desired, you can enable the Password on boot parameter.
  5. When you are done, press F10 to save the changes and exit the BIOS Setup Utility. If the verification is OK, the screen will display as following.

The password setting is complete after the user presses Enter.

If the current password entered does not match the actual current password, the screen will show you the Setup Warning.

If the new password and confirm new password strings do not match, the screen will display the following message.

The Ultimate Computer Repair Guide

The Ultimate Computer Repair Guide

Read how to maintain and repair any desktop and laptop computer. This Ebook has articles with photos and videos that show detailed step by step pc repair and maintenance procedures. There are many links to online videos that explain how you can build, maintain, speed up, clean, and repair your computer yourself. Put the money that you were going to pay the PC Tech in your own pocket.

Get My Free Ebook


Responses

  • christina
    How to set a acer 5515 laptop to out of the box settings?
    7 years ago
  • mateusz
    How to set laptop aspire high light?
    7 years ago

Post a comment