Advanced

The Advanced screen contains parameters involving your hardware devices. It also provides advanced settings of the system.

FIR Ports

Configure the system's infrared port using options: Disabled and Enabled.

Insyde Software SCU Main

Advanced

Parallel Port(LPT)

V Legacy USB support

Security

May 20, 2003 5:40:09 Boot

-FIR Ports-

Exit

  • I-'IR. I/O sellings—
  • Disabled ) COM1,3F8,IRQ4
  • COM2,2F8,IRQ3
  • COM3,3E8,IRQ4
  • COM4,2E8,IRQ3
  • Mode Selling for IRDA-
  • Normal (16550) ( ) IrDA (HPSIR)
  • ASK IR
  • FASTIR

<Tab> <Right> <Left> for block select. <Up> <Down> for item select. < Enter> for accept. <Cancel> <Esc> for reject. <Alt> activates accelerators. <Space> for Enable or Disable.

  • COM2,2F8,IRQ3
  • COM3,3E8,IRQ4
  • COM4,2E8,IRQ3
  • Mode Selling for IRDA-
  • Normal (16550) ( ) IrDA (HPSIR)
  • ASK IR
  • FASTIR
Insyde Software Scu

The table below describes the parameters in the screen. Settings in boldface are the default and suggested parameter settings.

Ports

Description

Option

FIR I/O Settings

Sets the base I/O address and IRQ for Infrared port.

COM1, 3F8, IRQ4/ COM2, 2F8, IRQ3/ COM3, 3E8, IRQ4/ COM4, 2E8, IRQ3

DMA Setting for Fast IR

Sets a DMA channel for the printer to operate in ECP mode. This parameter is enabled only if Mode is set to ECP.

DMA1, DMA2, DMA3,

Mode Setting

Normak (16550), IrDA (HPSIR), ASK IR, FAST IR

Configure the system's parallel port using options: Disabled and Enabled.

Insyde Software SCU

May 20, 2003 5:40:09

Advanced

Security

Boot

Exit

[¡Parallel Port(LPT)

V Legacy USB

May 20, 2003 5:40:09

Security

Boot

Exit

Insyde Software Scu

--DMA Setting For Fast IR--

( • ) DMA1

The table below describes the parameters in the screen. Settings in boldface are the default and suggested parameter settings.

Description

Option

Port Address

Sets the base I/O address for the parallel port. When Mode is selected as EPP mode, "3BC" will not be available.

LPT2, 278, IRQ5/ LPT3, 3BC, IRQ7

Port Definition

Sets the mode for the parallel port. Standard AT: Normal mode (AT compatible) Bi-directional: Bi-directional mod (PS/2 compatible)

Enhanced Parallel (EPP): EPP mode Extended Compabilities (ECP): ECP mode (requires DMA channel)

Standard AT (Centronics), Bidirectional (PS-2), Enhanced Parallel (EPP), Extended Capabilities(ECP)

DMA Setting for Fast IR

If ECP mode has been selected, then DMA default is DMA1.

DMA1, DAM3

Insyde Software SCU May 20, 2003 5:40:09

Main

Advanced

Security Boot Exit

Parallel Port(LPT)

Legacy USB keyboard Floppy Disk USB Mouse Support <Space> for Enable or Disable

Option

Description

Disabled

Disable support for Legacy Universal Serial Bus

Enabled

Enable support for Legacy Universal Serial Bus.

Security

The Security screen contains parameters that help safeguard and protect your computer from unauthorized use.

Insyde Software Scu Bios

The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings.

Was this article helpful?

0 0
Computer Hard Drive Data Recovery

Computer Hard Drive Data Recovery

Learn How To Recover Your Hard Drive Data After A Computer Failure.

Get My Free Ebook


Post a comment