Changing a Password

1. Use the t and i keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set Password box appears.

Set Supervisor Password

Enter Current Password Enter New Password Confirm New Password

  1. Type the current password in the Enter Current Password field and press Enter.
  2. Type a password in the Enter New Password field. Retype the password in the Confirm New Password field.
  3. Press Enter. After setting the password, the computer sets the User Password parameter to "Set".
  4. If desired, you can enable the Password on boot parameter.
  5. When you are done, press F10 to save the changes and exit the BIOS Setup Utility. If the verification is OK, the screen will display as following.

[

Continue

in saved. ]

The password setting is complete after the user presses Enter.

If the current password entered does not match the actual current password, the screen will show you the Setup Warning.

Setup Warning

Inva

Continue

zord. ]

If the new password and confirm new password strings do not match, the screen displays the following message.

Setup Warning

Passwo Re-e

rds do no nter pass

t match. word.

This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices includes the USB diskette drives, the onboard hard disk drive and the DVD drive in the module bay.

InsydelH20 Setup Utility

Rev. 3.5

Information

Main

Security Boot Exit

1. IDE0 : TOSHIBA MK2555GSX

2. IDE1 :

  1. Network Boot : Atheros Boot Agent
  2. USB HDD :
  3. USB CDROM :
  4. USB FDD :

Item Specific Help

Use <t> or 4 > to select a device, then press <F6> to move it up the list, or <F5> to move it down the list. Press <Esc> to escape the menu

Help Exit

Select Item Select Menu

Change Values Select ► Sub-Menu

Setup Default Save and Exit

Follow the on-screen instructions to adjust the order in which the devices boot.

Exit

The Exit screen allows you to save or discard any changes you made and quit the BIOS Utility.

InsydelH20 Setup Utility

Atheros Boot Agent Configuration Menu
The table below describes the parameters in this screen.

Parameter

Description

Exit Saving Changes

Exit System Setup and save your changes to CMOS.

Exit Discarding Changes

Exit utility without saving setup data to CMOS.

Load Setup Default

Load default values for all SETUP item.

Discard Changes

Load previous values from CMOS for all SETUP items.

Save Changes

Save Setup Data to CMOS.

The BIOS flash memory update is required for the following conditions:

  • New versions of system programs
  • New features or options
  • Restore a BIOS when it becomes corrupted. To run the BIOS flash utility:
  1. Copy the BIOS flash tool and the BIOS into a USB flash disk.
  2. Set the computer to boot from the USB flash disk. See "Boot" on page 29.
  3. On boot-up enter at the DOS prompt: C:\> flashit.exe v3106.fd /dc /beep:2000

Perform the following steps to use the DOS Flash Utility:

  1. Press F2 during boot to enter the Setup Menu.
  2. Select Boot Menu to modify the boot priority order, for example, if using USB HDD to Update BIOS, move USB HDD to position 1.

InsydelH20 Setup Utility

Rev. 3.5

Main

Item Specific Help

Boot priority order :

1. IDE0 : TOSHIBA MK2555GSX

3 Network Boot : Mheros Boot Agent I 4. USB HDD :

  1. USB CDROM :
  2. USB FDD :

Item Specific Help

Use < t> or <♦ > to select a device, then press <F6> to move it up the list, or <F5> to move it down the list. Press <Esc> to escape the menu

Help Select Item ■H/SH Change Values MJ9 Setup Default Exit Select Menu BsflltM Select ► Sub-Menu ¡¡jflj Save and Exit

3. Execute the FLASH.BAT batch file to update BIOS. The flash process begins as shown.

Insyda Flash Utility Tor

InsydeHZO

Uorslon 1.2m

InlHdlzlrq

riU loading IBS x

Currant BIOS Hods] nu

*G 1 JHTIfl

Hu» BIDS Hods I Ml

m ■■ jnria

Currant BIOS uorsiDTt'

ua.zi

BIBS wtton:

m.zs

i-i m™-ic *t rm

Wm

4. In flash BIOS, the message Please do not remove AC Power Source displays. NOTE: If the AC power is not connected, the following message displays.

C:NHDHvJATUI>flllsh jflllB0Z3

1 \HOMVJnnB> flash it Jflt 10823. fd /ft /B /DC

Uamning: Mo ftC power cotinecl

CINROK^JATÄ^

C:NR0HNJRT1B>_

te 1*310* hdmetheath

___-_—im-

Plug in the AC power to continue.

5. Flash is complete when the message Flash programming complete displays.

Perform the following steps to use the WinFlash Utility: 1. Put the BIOS:ZE8 v3106.fd file under WinFlash file root.

Organize * Include in library » Share with » New folder IJrE » |ji) @

Vi" Favorites

H Name

Datt modified

Type

Size

H Desktop

[J_ Ding.wav

4/24/20004:17 PM

Wove Sound

104 KG

£ Downloads

Bjf'j FlashTejter.ett

4/24/2008 4:17 PM

Application

252 KB

Recent PIbccs

H ¡FdPacker.exe

4/24/2008 4:17 PM

Application

320 KB

€ lnsydeFlash.exe

4/24/2008 4:17 PM

Application

612 KB

Libraries

^ ¡scfissh.dll

4/24/20034:17 PM

Application extens...

1,060 KG

j*j Documents

istflash.sys

4/24/2008 4:17 PM

System file

12 KG

tf1 Music

g ¡îcflaihx64.iyî

4/24/2008 4:17 PM

System file

24 KB

Pictures

platform.ini

6/10/2009 7:19 PM

Configuration sett...

5 KB

3 Videos

FtdeaseNotes.txt

4/24/20084:17 PM

Text Document

4 KB

[ C ZE8_v3106-fd

4/24/20034:17 PM

Application extens,.,

92 KG

iL- Computer

10/19/2009 7;30 PM

FD Rle

2,043 KG

Windows (CO

Z1PDLL.DLL

4/24/2008 4:17 PM

Application extens...

93 KB

  • a Recovery (D:)
  • a Recovery (D:)

1. Double click the WinFlash executable.

2. Click OK to begin the update. A progress screen displays.

3. When the process is complete, close all programs and applications and reboot the system.

0 0

Responses

Post a comment