Hardware Specifications and Configurations

Processor

Item

Specification

CPU type

Intel Mobile Pentium M processor at 1.4~1.7 GHz or higher

CPU package

uFCPGA package

CPU core voltage

Support automatic selection of power supply voltage

CPU I/O voltage

1.05 V

BIOS

Item

Specification

BIOS vendor

Insyde

BIOS Version

Insyde MobilePRO BIOS 4.0

BIOS ROM type

Flash ROM

BIOS ROM size

512KB

BIOS package

32 lead of TSSOP

Bupported protocols

ACPI 1.0b,PC Card 95, SM BIOS 2.3, EPP/IEEE 1284, ECP/IEEE 1284 1.7 & 1.9, PCI 2.2, PnP 1.0a, DMI 2.0, USB, VGA BIOS, CD-ROM bootable

BIOS password control

Set by setup manual

Second Level Cache

Item

Specification

Cache controller

Built-in CPU

Cache size

1MB or 2MB

1st level cache control

Always enabled

2nd level cache control

Always enabled

Cache scheme control

Fixed in write-through

System Memory

Item

Specification

Memory controller

Intel 855PM GMCH

Memory size

128MB/256MB/512MB/1GB

DIMM socket number

2 sockets

Supports memory size per socket

1024MB

Supports maximum memory size

2GB (by two 1024MB SO-DIMM module)

Supports DIMM type

DDR Synchronous DRAM

Supports DIMM Speed

200/266/333MHz

Supports DIMM voltage

2.5 V

Supports DIMM package

200-pin SO-DIMM

Memory module combinations

You can install memory modules in any combinations as long as they match the above specifications.

Memory Combinations

Slot 1

Slot 2

Total Memory

256/512MB

0 MB

256MB/512MB

256/512MB

256MB

512MB/768MB

256/512MB

512MB

768MB/1024MB

NOTE: Above table lists some system memory configurations. You may combine DIMMs with various capacities to form other combinations.

NOTE: Above table lists some system memory configurations. You may combine DIMMs with various capacities to form other combinations.

LAN Interface

Item

Specification

Supports LAN protocol

10/100 Mbps

LAN connector type

RJ45

LAN connector location

Rear side

Modem / Bluethooth Interface

Item

Specification

Data modem data baud rate (bps)

56K

Supports modem/bluetooth protocol

V.90 for MDC / Bluetooth 1.1 standard for BT modem

Modem connector type

RJ11

Modem connector location

Rear side

Hard Disk Drive Interface

Item

Specification

Vendor &

Model

Name

Toshiba 20G MK2023 GAS

Toshiba 30G MK3021 GAS

Toshiba 40G MK4021 GAS

Toshiba 60G MK6021 GAS

Hitachi 20G

IC25N02 0-

IC25N03 0-

IC25N04 0-

IC25N06 0-

ATMR04

Capacity (MB)

20000

30000

40000

60000

20000

30000

40000

60000

Bytes per sector

512

512

512

512

512

512

512

512

Data heads

2

2

3

4

1

2

2

3

Drive Format

Disks

1

1

2

2

1

1

1

(RPM)

4200 RPM

4200 RPM

5400

RPM

4200 RPM

4200 RPM

5400

RPM

Performance Specifications

Buffer size

2048KB

2048KB

2048KB

2048KB

2048KB

2048KB

2048KB

8192KB

Interface

ATA-5

ATA-5

ATA-5

ATA-5

ATA-5

ATA-5

ATA-5

ATA-5

Hard Disk Drive Interface

Item

Specification

Max. media

164.6~

154.3~

154.3~

154.3~

350

350

350

350

transfer

257.1

298.0

298.0

298.0

rate (disk-

buffer,

Mbytes/s)

Data

100 MB/

100 MB/

100 MB/

100 MB/

100 MB/

100 MB/

100 MB/

100 MB/

transfer

Sec.

Sec.

Sec.

Sec.

Sec.

Sec.

Sec.

Sec.

rate

Ultra

Ultra

Ultra

Ultra

Ultra

Ultra

Ultra

Ultra

(host~buffe

DMA

DMA

DMA

DMA

DMA

DMA

DMA

DMA

r, Mbytes/s)

mode-5

mode-5

mode-5

mode-5

mode-5

mode-5

mode-5

mode-5

DC Power Requirements

Voltage

5V(DC)

5V(DC)

5V(DC)

5V(DC)

5V(DC)

5V(DC)

5V(DC)

5V(DC)

tolerance

+/- 5%

+/- 5%

+/- 5%

+/- 5%

+/- 5%

+/- 5%

+/- 5%

+/- 5%

Optical Drive Interface

Item

Specification

Vendor & model name

Panasonic UJ-815

Performance Specification

CD-R/RW

DVD-ROM

Transfer rate (KB/sec)

(Mode1)

  1. 3X-24X CAV mode 3600KByte/s (Mode2)
  2. 3X-24X CAV 1769-4104KByte/s

3.3X-8X CAV 4.3MB/s-10.5 MB/s

Data Buffer Capacity

2 MBytes

Interface

IDE ( ANSI ATA/ATAPI-5)

Applicable disc format

DVD: DVD-ROM (DVD-5, DVD-9, DVD-10), DVD-R (3.95G/4.7G), DVD-RAM (2.6G/4.7G), DVD-RW CD: CD-Audio,

CD-WO

CD-RW

Photo CD

Video CD

Enhanced Music CD CD-TEXT

Loading mechanism

Load: The disc can be loaded semi-automatically ( To load the disc in the drive, it is needed to push the disc manually) Unload: The disc can be unloaded automatically by motor powered mechanism. The disc unloading can be operated by the Eject button or Eject Command through the IDE interface.

Power Requirement

Input Voltage

+5 V +/- 5 %

Audio Interface

Item

Specification

Audio Controller

Realtek ALC202A, AC97 Codec

Audio Interface

Item

Specification

Audio onboard or optional

Built-in

Mono or Stereo

Stereo

Resolution

20 bit stereo Digital to analog converter 18 bit stereo Analog to Ditial converter

Compatibility

Microsoft PC99, AC97 2.2 & WHQL

Mixed sound source

CD

Sampling rate

48 KHz

Internal microphone

No

Internal speaker / Quantity

Yes / 2

Video Interface

Item

Specification

Video vendor

ATI

Video name

M9+X

Chip voltage

Core/1.5V

Supports ZV (Zoomed Video) port

No

Video Resolution Mode (for both LCD and CRT)

Resolution

16 bits (High color)

32 bits (True color)

1024*768

Yes

Yes

1400*1050 (SXGA)

Yes

Yes

1600*1200 (UXGA)

Yes

Yes

1280*1024 (Monitor)

Yes

Yes

Parallel Port

Item

Specification

Parallel port controller

SMSC LPC47N227

Number of parallel port

One

Location

Rear side

Connector type

25-pin D-type connector, in female type

Parallel port function control

Enable/Disable/Auto (BIOS or operating system chooses configuration) by BIOS setup

Note: Depending on your operating system, disabling an unused device may help free systen resources for other devices.

Supports ECP/EPP/Bi-directional (PS/2 compatible)

Yes (set by BIOS setup)

Note: When Mode is selected as EPP mode, "3BCh" will not be available.

Optional ECP DMA channel (in BIOS setup)

DMA channel 1

Optional parallel port I/O address (in BIOS setup)

378h, 278h

Optional parallel port IRQ (in BIOS setup)

IRQ7, IRQ5

USB Port

Item

Specification

USB compliancy level

2.0

OHCI

USB 2.0

Number of USB port

3

Location

Rear side

Serial port function control

Enable/Disable by BIOS setup

PCMCIA Port

Item

Specification

PCMCIA controller

ENE CB1410 CardBus

Supports card type

Type II

Number of slots

One type-II

Access location

Left panel

Supports ZV (Zoomed Video) port

No ZV support

Supports 32 bit CardBus

Yes

System Board Major Chips

Item

Controller

System core logic

Intel 855PM and ICH4-M

Super I/O controller

SMSC 47N227, LPC interface

Audio controller

Realtek ALC202A Codec

Video controller

ATI M9+X

Hard disk drive controller

ICH4-M

Keyboard controller

ENE KB910

RTC

ICH4-M

Keyboard

Item

Specification

Keyboard controller

ENE KB910

Keyboard vendor & model name

Standard keyboard w/o launch button embeded

Total number of keypads

85 keys with 101/102 key emulation

Windows logo key

Yes

Internal & external keyboard work simultaneously

Yes

Battery

Item

Specification

Vendor & model name

Panasonic/Samsung

Battery Type

Li-ion

Pack capacity

63Wh

Battery

Item

Specification

Cell voltage

3.7V/cell

Number of battery cell

8

Package configuration

Pin 1: BATT+: Battery positive power pin

Pin 2: N/A

Pin 3: B/I: Enable Li-ion battery output, connect to 1k Q resistor to GND in system.

Pin 4: TS: Detector Battery

Pin 5: EC_SMD1: N/A

Pin 6: EC_SMC1: SMbus CLOCK

Pin 7: GND> EC_SMD1=SMbus DATA

Package voltag

Pin8: GND> Battery Ground Power Pin

LCD Inverter Specification

No.

Supplier

Model

Type

1

CMO

NI54I1-L02

15.4" WXGA

2

LG

LP154W01-A3

15.4"WXGA

3

Samsung

LTN154X1-L02

15.4" WXGA

4

LG

LP154W02-A1

15.4"WSXGA+

There are two control signals that come form system to control lamp brightness. One signal is named DAC_BRIG, which limits current to meet LCD lamp current specification. Another one is named PWM, which adjusts lamp brightness. This inverter brightness is adjusted by PWM burst mode. The PWM burst mode is that turning on and off the lamp at rate of 150Hz. The effective brightness is a function of the duty cycle.

Features

  1. Wide range 9V to 21V input voltage.
  2. Birghtness adjustment by PWM duty mode.
  3. Close loop controls lamp current.
Electrical Characteristics

No

Paramete r

Symbol

Min.

Typ.

Max.

Unit

Comment

1

Input voltage

NV PW R

9

14.8

21

*Note 1

2

Input current

Iin

--

0.33

--

A

3

Lamp current

IL

3.0

--

6.8

mA

DAC=0V *Note 2

4

Lamp current

IL

2.7

--

6.3

mA

DAC=1V

4

Frequenc y

F

45

55

65

KHz

* Note 3

5

Output power

Pout

--

--

4.5

W

6

Efficiency

n

80%

--

--

--

7

Starting voltage

Vs

1600

--

---

V

At 0'C

8

Starting time

Tvs

1

--

1.5

Sec

9

Dispoff#

2.8

3.3

3.6

V

Backlight on/off signal

0

0.5

0.8

V

Low level

10

Limited lamp maximum current

DAC-BRIG

0

3.3

V

*Note 2

11

PWM signal *Note 4

INV PW M

142

150

158

Hz

PWM signal frequency

3.0

3.3

3.6

V

PWM signal amplitude

30

100

Period

12

Lamp current overshoot

I zero-PK

10

%

Line transient (10.8V to 21V/100us) and turn on transient

13

Current Wavefor m factor

1 rms

1.27

Jl

1.56

or ^rms *10

14

Unbalanc e Rate

-10%

0

+10%

Mulitpl e

^rms

15

Turn off current (Hight side)

IHl

0

A

PWM=30%

No

Paramete r

Symbol

Min.

Typ.

Max.

Unit

Comment

i5

Turn off voltage (Low side)

Voff

i50Vp -p

V

PWM=30%

i6

Voltage Rise time (Low side)

Trise

300us

us

PWM=30%

i7

Voltage fall time (Low side)

Tfall

S00us

us

NOTE:

  • 1. The inverter can work in 7.5V input voltage (continuous), but 7.5V electronic characteristic will not be care.
  • 2. Limited lamp maximum current by DAC_BRIC signal: When DAC_BRIG voltage is 0V and INV_PWM enables (100%), lamp has max. current. When DAC_BRIG voltage is 3.3V and INV_PWM enables (100%), lamp has min. current. When add 1V DAC, the 100% Lamp current will decrease 0.5mA.

DAC_BRIG signal comes from system chipset with internal resistance of 3K Q

  • 3. Inverter operating frequency should be within specification (45~65kHz) at max. and min. brightness load.
  • 4. INV_PWM enable implies INV_PWM signal is High level (On duty cycle is 100%). It is a square wave of 150Hz to adjust backlight brightness that is a function of PWM duty cycle. Backlight brightness is maximum value under INV_PWM at 100% and brightness is minimum under INV_PWM at 30%.
  • 5.The system interface signals belong to 3.3V.
  • 6. Please make sure open lamp output voltage should be within starting voltage specification.
  • 7. Inverter should pass human body safety test.
  • 8. Inverter should be no smoking by any component open/short test.
  • 9. Transformer voltage stress should not be over 85% under any condition.
  • turn on overshoot transient and line transient.) *10. Audio noise should be less than 36dB at 10cm distance.
Electrical specification

No

Symbol

Min.

Typ.

Max.

Unit

Comment

1

V oper*

--

650

--

Vrms

Lamp operating voltage (650+/-50)

II

6.2

6.5

6.8

mArms

DAC BRIG: 0 V, PWM: 100%

II

3.0

3.3

3.6

mArms

DAC BRIG: 0 V, PWM:30%

Il

5.7

6.0

6.3

mArms

DAC_BRIG: 0V, PWM:100%

Il

2.7

3.0

3.3

mArms

DAC_BRIG: 1V, PWM:30%

F

45

55

65

kHz

h

80%

--

--

--

All components on inverter board should follow below rules:

  1. Component using conditions (component stress) must be within component specification including voltage rating, current rating, temperature etc.
  2. Component temperature should follow below:
  • AT <=450 degree C, at 25, 35 degree C.
  • Component temperature should be less than 80 degree C inside system at 35 degree C. LCD

Item

Specification

Vendor & model name

LTN154X1-

L02

LP154W01-A3

LP154W02-A1

Mechanical Specifications

LCD display area (diagonal, inch)

15.4"

15.4"

15.4"

15.4"

Display technology

TFT

TFT

TFT

TFT

Resolution

WXGA (1280* 800)

WXGA (1280* 800)

WXGA (1280* 800)

WSXGA+ (1650* 1050)

Supports colors

262K

262K

262K

262K

Optical Specification

Brightness control

keyboard hotkey

keyboard hotkey

keyboard hotkey

keyboard hotkey

Contrast control

No

No

No

No

Suspend/Standby control

Yes

Yes

Yes

Yes

Electrical Specification

Supply voltage for LCD display (V)

3.3

3.3

3.3

3.3

Supply voltage for LCD backlight (Vrms)

650

690

690

690

AC Adapter

Item

Specification

Vendor & model name

Delta ADD-65DB Liteon DA-165G-G2CR

Input Requirements

Maximum input current (A, @100Vac, full load)

1.5A [email protected]/100Vac and 240 Vac

Nominal frequency (Hz)

47 - 63

Frequency variation range (Hz)

47 - 63

Nominal voltages (Vrms)

90 - 264

Inrush current

The maximum inrush current will be less than 50A and 100A when the adapter is connected to 100Vac(60Hz) and 240Vac(50Hz) respectively.

Efficiency

High efficiency 85% minimum, at 100~240Vac AC input, full load, warm-up condition.

Output Ratings (CV mode)

DC output voltage

Offers constant voltage 19.0V output source with 65W max output power capacity.

Noise + Ripple

300mvp-pmax (20MHz bandwidth) for resistor load

Output current

0 A (min.) 3.5A (max.)

Output Ratings (CC mode)

DC output voltage

18.G ~ 2G.G

Constant output

3.5A

Dynamic Output Characteristics

Start-up time

3 sec. (@115 Vac and 230Vac full load)

Hold up time

5ms min. (@115 Vac input, full load)

Over Voltage Protection (OVP)

25V

Short circuit protection

Output can be shorted without damage, and auto recovery

Electrostatic discharge (ESD)

15kV (at air discharge) 8kV (at contact discharge)

Dielectric Withstand Voltage

Primary to secondary

4242 Vdc for 1 second

Leakage current

60uA at 240Vac/60Hz

Regulatory Requirements

  1. FCC class B requirements (USA)
  2. VDE class B requirements (German)
  3. VCCI classll requirements (Japan)
Power Management

ACPI Mode

Power Management

Mech. Off (G3)

All devices in the system are turned off completely.

Soft Off (G2/S5)

OS initiated shutdown. All devices in the system are turned off completely.

Working (GG/SG)

Individual devices such as the CPU and hard disk may be power managed in this state.

Power Management

ACPI Mode

Power Management

Sleeping State (SS)

CPU Power Down VGA Power Down PCMCIA Suspend Audio Power Down Hard Disk Power Down Super I/O Power Down

Sleeping State (S4)

Also called Hibernate state. System saves all system states and data onto the disk prior to power off the whole system.

Environmental Requirements

Item

Specification

Temperature

Operating

+5 ~ +35°C

Non-operating

-20 ~ +65°C

Non-operating

-20 ~ +65°C (storage package)

Humidity

Operating

10% to 90% without condensation

Non-operating

10% to 90% RH, non-condensing (unpacked)

Non-operating

10% to 90% RH, non-condensing (storage package)

Vibration

Operating (unpacked)

5 ~ 500Hz: 0.9G

Non-operating (unpacked)

5 ~ 500Hz: i.SG

Mechanical Specification

Item

Specification

Dimensions

330mm (W) x 273mm (D) x 31.7mm (H) for 14.1/15.0 inch model

Weight

6.11lb (2.77kg) for 14.1 inch model (8 cell battery) 6.41lb (2.9kg) for 15.0 inch model (8 cell battery)

I/O Ports

One type II CardBus slots, One RJ-11 modem jack,One RJ-45 network jack, One DC-in jack for AC adapter, One ECP/EPP-compliant parallel port, One external monitor port, One headphone/speaker/line-out jack (3.5mm mini jack), One microphone/line-in jack (3.5mm mini jack), One S-video-out (NTSC/PAL) port, Three Universal Serial Bus (USB) ports, One IEEE 1394 port.

Drive Bays

One

Material

Recycle plastic PC+ABS 94V0

Indicators

Power, Media activity, Battery charge, Wireless/Bluetooth communication, Caps lock, Pad lock, Num lock and Scroll lock indicators

User define switch 1, 2 Wireless ON/OFF switch

Memory Address Map

Memory Address

Size

Function

000E0000h-000FFFFFh

128KB

System BIOS

000C0000h-000CFFFFh

64KB

VGA BIOS

000A0000h-000BFFFFh

128KB

Video memory (VRAM)

00000000h-0009FFFFh

640KB

Conventional memory

I/O Address Map

I/O Address

Function

0000-001F

Direct memory access controller

0000-0CF7

PCI bus

0010-001F

Motherboard resources

0020-0021

Programmable interrupt controller

0024-0025

Motherboard resources

0028-0029

Motherboard resources

002C-002D

Motherboard resources

002E-002F

Motherboard resources

0030-0031

Motherboard resources

0034-0035

Motherboard resources

0038-0039

Motherboard resources

003C-003D

Motherboard resources

0040-0043

System timer

004C-004F

Motherboard resources

0050-0053

Motherboard resources

0060-0060

Standard 101/102-Key or Microsoft Natural PS/2 Keyboard

0061-0061

System speaker

0062-0062

Microsoft ACPI-Compliant Embedded Controller

0064-0064

Standard 101/102-Key or Microsoft Natural PS/2 Keyboard

0066-0066

Microsoft ACPI-Compliant Embedded Controller

0070-0071

System CMOS/real time clock

0072-0077

Motherboard resources

0080-0080

Motherboard resources

0081-008F

Direct memory access controller

0090-009F

Motherboard resources

00A0-00A1

Programmable interrupt controller

00A4-00A5

Motherboard resources

00A8-00A9

Motherboard resources

00AC-00AD

Motherboard resources

00B0-00B5

Motherboard resources

00B8-00B9

Motherboard resources

00BC-00BD

Motherboard resources

00C0-00DF

Direct memory access controller

00F0-00FE

Numeric data processor

0170-0177

Secondary IDE Channel

I/O Address Map

I/O Address

Function

01F0-01F7

Primary IDE Channel

0200-020F

Motherboard resources

0274-0277

ISAPNP Read Data Port

0279-0279

ISAPNP Read Data Port

0376-0376

Secondary IDE Channel

0378-037B

ECP Printer Port (LTP1)

03B0-03BB

Intel(R) 82852/82855 GM/GME Graphics Controller

03C0-03DF

Intel(R) 82852/82855 GM/GME Graphics Controller

03F6-03F6

Primary IDE Channel

03F8-03FF

SMC IrCC - Fast Infrared Port

04D0-04D1

Motherboard resources

0778-077B

ECP Printer Port (LTP1)

07F8-07FF

SMC IrCC - Fast Infrared Port

0A79-0A79

ISAPNP Read Data Port

0D00-FFFF

PCI bus

1000-107F

Motherboard resources

1100-110F

Intel(R) 82801DBM Ultra ATA Storage Controller - 24CA

1200-121F

Intel(R) 82801DB/DBM USB Universal Host Controller - 24C2

1300-133F

Motherboard resources

1400-141F

Intel(R) 82801DB/DBM SMBus Controller - 24C3

1600-161F

Intel(R) 82801DB/DBM USB Universal Host Controller - 24C4

1700-171F

Intel(R) 82801DB/DBM USB Universal Host Controller - 24C7

C000-C0FF

Realtek RTL8139/810x Family Fast Ethernet NIC

C100-C17F

VIA OHCI Compliant IEEE 1394 Host Controller

E000-E007

Intel(R) 82852/82855 GM/GME Graphics Controller

E100-E1FF

Realtek AC'97 Audio

E200-E23F

Realtek AC'97 Audio

E300-E3FF

Agere Systems AC'97 Modem

E400-E47F

Agere Systems AC'97 Modem

FD00-FDFF

ENE CB1410 Cardbus Controller

FE00-FE00

Motherboard resources

FF00-FFFF

ENE CB1410 Cardbus Controller

IRQ Assignment Map

Interrupt Channel

Function(Hardware)

IRQ00

SystemTimer

IRQ01

Standard 101/102-Key or Microsoft Natural PS/2 Keyboard

IRQ04

SMC IrCC - Fast Infrared Port

IRQ08

System CMOS/real time clock

IRQ09

Microsoft ACPI-Compliant System

IRQ12

Alps Pointing-device

IRQ13

Numeric data processor

IRQ14

Primary IDE controller

IRQ Assignment Map

Interrupt Channel

Function(Hardware)

IRQ15

Secondary IDE controller

IRQ10

Agere Systems AC'97 Modem

ENE CB1410 Cardbus Controller

Intel(r) 82801DB/DBM USB 2.0 Enhanced Host Controller - 24CD

Intel(R) 82801DB/DBM USB Universal Host Controller - 24C2

Intel(R) 82801DB/DBM USB Universal Host Controller - 24C4

Intel(R) 82801DB/DBM USB Universal Host Controller - 24C7

Intel(R) 82852/82855 GM/GME Graphics Controller

Realtek AC'97 Audio

Realtek RTL8139/810x Family Fast Ethernet NIC

VIA OHCI Compliant IEEE 1394 Host Controller

DMA Channel Assignment

DMA Channel

Function(Hardware)

1

ECP Printer Port (LPT1)

3

SMC IrCC - Fast Infrared Port

4

Direct memory access controller

The Ultimate Computer Repair Guide

The Ultimate Computer Repair Guide

Read how to maintain and repair any desktop and laptop computer. This Ebook has articles with photos and videos that show detailed step by step pc repair and maintenance procedures. There are many links to online videos that explain how you can build, maintain, speed up, clean, and repair your computer yourself. Put the money that you were going to pay the PC Tech in your own pocket.

Get My Free Ebook


Post a comment